Bidet Toilet Attachment, Self Cleaning, Hot and Cold Function, Ergonomic Lever, Feminine (Front) and Back Clean, Easy DIY installation, Non-Electrical, INCLUDES BUMPERS

This is my first bidet and I'm loving it! All the necessary parts and tools are included. Instructions and diagrams were easy to follow, so it took me only about twenty minutes to install. The bumpers included are still sticking firmly to the toilet rim. It only ads a few seconds to bowl cleaning, as it comes with a self-cleaning feature. Nothing is leaking, at least not so far. I did not install the hot water connection due to my hot nozzle being located too far away from the toilet nozzle - which is OK because it takes too long for my water to heat up anyway (I live in SoCal, if you live in a freezing cold climate please connect hot water!).As a bidet virgin, it took a short while to figure out the controls. After a bit of practice, I can work the bidet by touch. The female spout position is a huge plus! Just make sure you don't pull the pressure bar up all the way...Youch!! You might as well stick a fireman's hose back there and crank the water to full pressure. XDThe only real complaint I have is that the plastic this bidet is made if doesn't seem to be as strong as it should be. So be careful not to ever put weight on it or it may break at the middle.Using a bidet has me feeling cleaner than I've ever felt to the point where I'm angry at myself for not getting one years ago. This particular bidet is working out great for me so far. My guests also love it and I plan on buying another one for my Besty on her birthday.

The setup was very straight forward, easy to get going with my first bidet. It wasn't perfect with my toilet, mostly because the feet don't work well with the curved surface of the bottom of my seat. Sticking to the existing feet did not allow it to lay flat. That being said, it raises the seat a lot, probably about an inch. So just make sure you're okay with this. Everything else was super easy.I haven't setup the temperature control because running the tube through the cabinet in my bathroom won't be very tidy. It does come with a cap to cover the hot inlet and can be used with only cold.With only cold water its plenty strong to clean my bottom, it can be a little strong for the sensitive bits though. This can easily be worked around with throttling back the power at the spout, or lowering the intensity on the bidet itself.Does what I need, we'll see how long it lasts.

If you have older plumbing in an older home this is not recommended. My sister and I attempted to install but the plumbing was rustic in our home and had a total disaster. When my sister was turning the hot water off so we could detach the tubing and attach the bidet tubing, the handle broke and water started spilling everywhere. Went to the garage to shut the water off in the house and it was rusty as well and did not work. Finally found the knob on the corner that turns the water off in the house but by then the water had flooded into the hallway, living room, closets, and two bedrooms. Needless to say, the whole carpet had to be removed in the house and replaced. I wouldn't be able to review the actual bidet because we didn't even get to install it.

I was a bit concerned as there had not been any reviews yet. However, the installation instructions were very easy to follow and it was installed with no problems. the unit works great just as described. I have been using it for a couple weeks now and have experienced no problems. The included spacers were a thoughtful and necessary addition.Overall, I think I made a great purchase. I will buy it again.

Pretty good bidet with all the parts you need to do proper setupOf the bidet. You will need an adjustable wrench and screwdriver to do the installation. Also make sure you have enough Teflon tape to do the job since it doesn’t come with much. T-adapters leak if you don’t. Use Teflon tape enough make sure to go at least 3 full turns on the windings. Also be sure to use gloves since the winding on the t-adapters are sharp.

Installing the bedit was easy. Once installed, I couldn't get the nuts on the toilet to stop leaking. When I attched the hot water, I was unable to get water to come out the bedit. I have tried to contact the company, but their information is not available.

This is my 2nd bidet. Overall I am happy with it but, as a bigger guy I find the water control lever is against my leg, which causes the knob to go to the hot side. I would have preferred more "leg room" so to speak. Otherwise tho a good upgrade from my 1st. Very thorough cleaning. Also when I bought my first one I remember having to go buy plumbing parts to fit my setup. This kit worked perfectly with the existing plumbing.

Easy to install. It takes the warm water a while to get where it needs to go, but the cold water isn’t as bad as I thought it would be.