EXZEIT Waterproof Led Boat Lights, 2 pc 72W Deck/Dock Marine Lights 4000LMS 180°Flood Light, 6.3inch, 12/24 V Led Light Bar

Mounted these on a pontoon boat to use when docking at night, very bright lights, barely noticeable size

Update for all those asking about power consumption. I just received this answer from Exzeit: "There are 12 OSRAM lens in one light. Each lens is 1.5W. So in total, it is 36 W per light. But under actual working state, to lenthen the lens life, the power consumption has been controlled to about 20W per light. Brightness wont be affected." I've been there, done that, bought the cheapy $20/pair LED spreader lights....sure, they LOOK the same...they might even be the same brightness as this set for ~$18 more....BUT I watched one of my old pair of $20/pr. lights burn out in front of me due to rain leaking inside ! 🤬 Check out the photos carefully before you buy....THIS set clearly uses a nice fat rubber grommet where the wire enters the housing...making it IP68 WATERPROOF ! Those cheapies don't...no grommet?...not trustworthy !...they distort and exaggerate their ratings, as if "waterproof" and "water resistant" were the same thing....as they say in the world of Capitalism..."Buyer Beware!"...KNOW the important specs about the product you're buying! In addition to real waterproof, these are 3x or 4x brighter than my old set...I've included some pics of one old light (left) and one new light (right)...BIG improvement ! (then I changed out the old one of course 😉) Another GREAT improvement in these compared to the cheapies is PRE-TINNED 16 guage wire compared to horrible, dirty quality 18 or maybe 20 guage wire in my old lights...the kind of dirty copper you have to scrape the copper oxide off with an Exacto or other blade till it's nice and bright copper...otherwise solder will just ball up and not even stick ! 🤬 (In the marine environment, do yourself a favor, crimp AND solder, THEN marine-grade shrink tubing...you'll never have to do this again) The only slight negative "ding" I would give this set is the U-shape mounting bracket is NOT stainless, it's painted/powder-coated...probably steel....only the allen screws and nuts and washers are stainless.....ironically..my old lights came with 100% stainless hardware, including the U-bracket ! 😯 Unfortunately, my old stainless brackets wouldn't fit these new lights. 😥 But the powder coating looks thick enough, I probably won't see the new brackets rusting in my lifetime. 🙂 I wasn't too happy with the allen screws either, a little harder to access and tighten compared to a standard hex bolt....so I added some Loctite to the threads as I assembled, so I wouldn't have to be climbing my sailboat mast to tighten loosened allen screws ! 🙄 Do yourself a favor, buy better, one time...buy these! (Or glob some 3M 4000 or 5200 polyurethane marine sealant into the wire hole on those cheapies and cross your fingers ! 😉)

Lights are bright and easy to install.

I’ve bought these twice… three years apart. My first set held up “well” in a gulf environment as “spreader lights” for my yacht. Never a problem with water intrusion, and the lights are very bright with a good “flood” spread. As is common with painted or powder coated aluminum devices, I started to see some corrosion and paint flaking on one unit after 3 years. At this price it just makes more sense to replace instead of repainting. Ordered and received the second set. Very minor mechanical design changes over the years, but largely imperceptible to the casual eye. Installed one unit…. equally bright to my original set, but the color has changed slightly. Old units produce a VERY white light, bordering on blue-white. Newer unit is a bit “warmer” in color. Not really a big deal, especially if you’re not mounting a “new” unit next to an “old” one.

Great product. I bought a two sets of 2 these LED lights to be used as spreader lights mounted to the front and rear of the T-top on my totally refurbished Cape Horn 22' center console boat. However the light brackets required drilling into the T top tubes to mount them and I did not want to do that. I found Nilight Horizontal Bar Clamp Mounting Bracket Kit for Off-Road LED Light Bars on Amazon for mounting on round tubes of off road vehicles and figured if they would be good for off road use they should work well for the abuse of running the boat in 3-4 foot seas. I painted the brackets white to match the lights and T-top tube color and they look great. Together they were perfect for this boating application even though not necessarily advertised for it.

these are the second set i buy and they are great. Ive had the first set installed on each end for and aft of my radar arch for over a year and they still work great. The high end stuff costs 8 times as much and have friend at the dock that are already changing them out after a year and asking me where I got mine and they cant believe how nice they are. and tell me they are going to buy them This second set will be mounted inside my hydraulic engine hatch and will light up my engine room.

Purchased to replace old halogen desk lights on my 25ft fishing boat. Easy replacement using new brackets and hardware on the T top mounting points. MUCH brighter than the old halogens with great coverage, light is very white and natural. Power consumption noticeably much lower than the halogens. Overall look is really nice, sturdy and functional.

Bright as can be, and seem well made enough to handle the salt-water environment. Time will tell, but so far - no complaints.

primera impresión , muy buena calidad , ahora los instalaremos para ver cómo funcionan , llegaron a tiempo

Excellent product

満足しております。取り付け金具がステンレスだともっといいかな？

Good Product & genuine seller. This product fulfilled our requirements.

The lights are super bright and were a huge asset to our pontoon boat. For the purchase price these are fantastic. At night they are really bright and light up the entire dock area where we keep the boat. During the day the lights can also be seen from far away increasing safety during lower visibility situations.