CONFAST 3/16" x 1-3/4" Hex Head Concrete Screw Anchor with Drill Bit for Anchoring to Masonry, Block or Brick (100 per Box)

I used this to repair a corner pop on my foundation. The original material was lost so I had to form a new one. I used this anchor screw to provide support for the new corner. I drilled into the old concrete, added in an epoxy for anchors, placed the screws tightly, let it dry, setup a form, then troweled in the new concrete. Repair looks good (professional even), and seems very stable (time will tell). To determine the correct size, you need to decide how deep the screw will be set. I wanted mine sticking out by 1.5 inch to act as rebar for the concrete, and drilled about 1.25 inches deep into the existing foundation, so I used 2.75 inch long screws. If anchoring other material, then consider it's width plus the depth you want the screw to be drilled. Be sure to use an anchor epoxy for a permanent fix. A note about drilling the holes for these screws: There are a LOT of drill bits advertised as good for concrete, they aren't. You need a fairly long bit (longer than the length of the screw to be set in the concrete) and it needs to be a REAL CONCRETE DRILL BIT - like the "Bosch BM5000 Fast Spiral Masonry Set". You must use the correct bit width or you can damage the concrete (if too narrow a bit) or the screw won't hold (if too wide a bit). Length is really difficult to get right if you are working in a confined area, so take that into account. If you have a wide open work area then you need to determine how deep you want to set the screw and be sure you have a slightly longer bit - put a piece of tape on it to show how far in to drill and when the tape aligns with the concrete you stop. If you have a really confined area like I did, you need to also determine how much extra bit you need to fit into the area to even reach the drill drill point (I could get the drill about 2 to 3 inches away from the drill hole and no closer). This means you have to add that much to the overall length of the bit for your project to work. Finding long enough masonry drill bits can be a real problem.

A bargain price for 100 that also includes a solid masonary bit when compared to name brand prices and performed just as good. I bought extra bits and you can see I never opened the package. Bit took a beating without being changed while drilling over 48 holes into grout in between bricks in the columns that support my home. 4 of the holes that I drilled didnt tighten up but was easily remedied by using a larger 1/4" scew. Never snapped any heads off. Would by again. Very pleased.

You won't find this length in a box store, which is why I purchased online. The plus is the screws work just as well as tapcon screws which depending on your concrete is mixed. If its soft it will strip out if torqued to much and if its really hard you might snap them while seating the head. I had decent success in fully cured foundation wall some I had to finish setting with my hammer but still has hold. Only real complaint is it should come with a couple bits mine worked good first 20 holes but got dull in hard concrete, good luck finding a bit this size. I had to put the boards up drill with shorter bit and remove to finish holes to get required depth. My advice see if they sell extra bits and buy a few more but good buy on the screws.

We use about 50 a week and maybe I've broken the head off of 3 of them in the past 4 months. Honestly, that's most likely only because my guy was using too much tork with my impact driver. Going full throttle while the thing is already set. Yea, they might break then. If you know how to use a drill. You shouldn't have an issue. These are good screws. Much better than buying 15 for the same damn price at my local hardware store.

First off, if you are trying to drill into concrete or brick you need a masonry drill bit and a hammer drill. Otherwise, you will spend long hours trying to drill a short hole. I had been drilling holes for plastic wall anchors into concrete but they could pull out fairly easily. So, I decided to try these screws that directly screw into the concrete. They even come with their own masonry drill bit. Let's just say that I will be using these from now on. I needed to mount a steel wall rack for storage bins onto a concrete wall. To be honest, I was kind of dreading this project because it was going to take a chunk of my Saturday. The drill went through the concrete like butter and the screws screwed tightly into the wall. The whole mounting project probably took 5 minutes.

Good brand works well

Super impressed by these! I’ve gotten so much use out of it and made a lot of money from it too. I’ve used these two install downspouts for gutters, I’ve also used it to install vents for dryers on the outside. These guys have no issue going through the material. I would recommend First doing a Masonary bit to go through the area, you are going to be securing, once you’ve done that, though, this guy has no problem and it bites really well. Many other screws seem to not hold very well and eventually come right off the wall. These guys are awesome.

Excellent product and service. Will buy from them again.

They did what the were designed to do, and well. But honestly, the cost of fasteners now, and these were the least costly of the bunch.

These screws are heavy and high quality. The hex head makes it easy to drive, and a 3/16" masonry bit was the perfect pilot. However, I want to take 1 star off because unlike the description, these screws did NOT include a drill bit.

avevo già utilizzato negli stati uniti con risultati buoni,ottimo se si usa con tasselatori vibranti e non impulsi ,ottimo per fissare profili pezzi che richiedono viti continue senza segnare togliere e forare

En las especificaciones RECOMIENDAN utilizar broca de 3/16" sin embargo a mí no me funcionó así, quedaban bailando con tornillos, tal vez por el tipo de material, lo mismo ocurrió con los TAPCON, ambos incluyen sus brocas pero no logré el efecto deseado por lo que decidí ir por una broca más pequeña. En este caso ocupé una broca SDS de 5/32" y el efecto logró ser el esperado, algunos tornillos siguen girando al llegar a tope (por extracción saldría con mucha facilidad) con esta combinación de broca y tornillo quedó muy sólido.

Had no trouble with the screws however the included bit was too short.