Muzata 20Pack 6.6FT Silver LED Strip Channel with Milky Diffuser U1SW WW

Very good quality, especially for the price. Looks great and is easy to install. Will not completely hide the hot spots but will dull them to about half way, which was enough in my case. I was slightly worried reading the reviews about some difficulty pushing the diffuser into the metal bar but had no issues whatsoever. I assume people are having hard time if they don't align the diffuser properly or they push in one side at a time instead of snapping in both edges simultaneously, from one end to the other. Fairly easy to cut with some basic tools but make sure to smooth the edges as they get very sharp after cutting.

I don’t understand all the negative comments about installing the diffuser in the track. It easily snaps in by starting at one end then pressing it down bit by bit to the other end. You DO NOT slide the diffuser in the track; the fit is far too tight. Simply push one side in the groove on the track then snap the opposite side of the diffuser in with your thumb or fingers. Easy Peasy! The aluminum track, or channel, is very easy to trim to length with a hacksaw, Dremel or similar. The diffuser can be trimmed to length with a razor knife. The tracks come with 2 mounting clips per channel, which were very easy to install with a single tiny screw in each. One could easily substitute 3M foam LED mounting tape if preferred. Just be sure to clean the mounting surface with alcohol before mounting. The shape of the LEDs can still be seen thru the diffuser, but it is so much better than seeing the reflection of the bright LEDs without the diffusers. It may be that for the LEDs to not be very visible one would need LED strips with more LEDs located closer together. Fo example, instead of a 300 LED strip, try a 600. I am totally pleased with these and would buy them again. My wife loves them. They replaced halogen under-cabinet puck lights.

I was concerned that the new COB lightstip I installed over my kitchen cabinets were putting out a lot of heat and since they were simply laid on top of the cabinets, had begun to twist out of place. Since I never removed the backing from the COB lightstrips, I was able to adhere them to the metal channel. The metal channel acts like a heatsink and I feel safer. Now after a week, they are still in place. The 6mm height are tall enough for them not to be seen from the front of the cabinet. I opted not to use the plastic cover due to the light reduction with the cover on. I love them and they were easy to install.

I used these for a kitchen project to run led strips as under-cabinet lighting. Generally speaking, the installation of these is pretty simple, mount the clips to your surface and snap the track into place. Mounting them under a cabinet posed it's own challenges but once done the installation was clean, and I'm very happy with the results. The clips hold the track solidly under the cabinet and the channel is low profile enough that it's almost unnoticeable under the cabinet. The channel and diffuser will offer solid protection from the kitchen elements, which is important as this particular light was going over the stove and cabinets next to the stove. The diffuser was a bit of a challenge to install as it fits very tight within the channel. Once you figure out the trick it goes in OK, getting it started was a bit tricky, especially trying to work upside down under a cabinet. They're also a bit stingy with the clips. My kit only came with enough clips to do 2 per section which didn't feel like enough to me. So I ended up using all 12 provided clips on 4 sections of channel. A few extra clips in the bag would be nice. But in the end it worked out. I did install a single 30" section and ended up just drilling a couple of holes and using small wood screws to mount it, which also worked fine. Overall I'm satisfied. The quality seems good enough, and the fit and finish of the end result is very unobtrusive. The diffuser doesn't impact the brightness of the LEDs any noticeable amount, and the lights look great in that area.

Great quality use them for strip lights on my steps outside. They look amazing. Lots of compliments.

Very slim with a low profile. Skip the mounting clips and use doubled side tape instead

No cardboard tube but instead the channel is shipped wrapped in plastic with bubble wrap on the ends. Mine arrived with 6 out of the 10 pieces bent, and because I had a project that couldn't wait for a replacement shipment I used the 4 that were straight and am stuck with the remaining pieces. On the bright side, the diffusers snap positively into the channel and the whole thing cuts cleanly with a fine tooth aluminum/plastic blade on a miter saw.

Used along with LED COB lighting strips to add under cabinet lighting in our kitchen. Needed to do for a long time and finally had the time and courage to tackle it. We were nervous at first with doing our own DIY setup instead but it seems that the options have come A LONG way in the past decade. Hubby watched a Youtube video of someone doing similar project and it seemed easy enough. Definitely more complicated than getting the pre-made kits, which I'm sure work great but were more expensive and less customizable.... Anyway, back to these tracks, hubby said he was surprised with how easy they cut - he even was able to use compound miter saw with normal blade he uses for woodworking. He attached the dampener to it prior to cutting to avoid having to cut the plastic dampener and the metal track separately. Used painters tape and cut slowly and it worked great - no issues with that. He also used the provided clips to attach the tracks to the cabinets. BE CAREFUL or you could go through the underside. He pre-drilled to just the right depth and had no issues with the install - no screws stripped or tore through the cabinet. You could (as others have recommended) use some double sided adhesive tape but he liked the idea of being able to remove easily in case the lights need repairing down the road - soldering upside down is NOOO FUN =) His only 'complaint' was that the little end caps that come with the system wouldn't work with our setup. Half of the caps come with a small (maybe 1/8 inch) hole to feed wires through and the other half are closed off. He had to drill larger holes due to using 18 gauge wires for a longer run and didn't want the possibility of voltage drop. We only needed 1 end piece after connecting all 6 of our lighting bays together. Definitely an 'our situation' problem and nothing against the product. They'd be great as-is if you're doing 6 separate bays and not connecting them.

Good quality product. Easy installation.

Ces canaux LED en aluminium se sont avérés faciles à installer, avec un système de fixation simple qui ne demande pas d'outils compliqués. Combinés avec mes bandes LED WiZ de 5m, le résultat final est vraiment esthétique, le boîtier diffuse bien la lumière tout en cachant proprement la bande elle-même pour un look plus soigné et professionnel. Le couvercle s'insère bien dans le canal en U, sans jeu excessif, et donne une belle finition uniforme à l'éclairage une fois allumé. L'aluminium semble robuste et de bonne qualité, avec un lot de 6 mètres qui couvre amplement un projet d'éclairage de bonne taille. Une belle combinaison qui élève vraiment l'apparence d'une installation LED comparé à une bande nue collée directement sur une surface. Facile à installer et le rendu visuel en vaut vraiment la peine!

Does nothing to hide LED dots. Absolutely do not buy this product.

This is the worst defuser, you can clearly see the led dots. I don’t recommend

Very good nice sleek tidy look easy to use and cut to length good value for money as an electrician I use these all the time