Electrically Conductive Paint 50ml - Water-Based Carbon Coating for Guitar Shielding, PCB & Remote Control Repair - Matte Black EMI/RF Shield

used to repair my second Netatmo exterior weather sensor, first one was replaced by Netatmo, this one is outside warranty. fully functioning again, lovely stuff

I wanted to shield the control cavity of an electric guitar I’m putting together. I applied the paint and waited a few days. I’ve completed the wiring and grounded the painted sides of the cavity, creating a Faraday cage. It works in shielding the guitar from noise. But the paint hasn’t dried to a sealed surface, it has dried as a carbon particle powder. If I touch the sides of the cavity, I get black powder on my fingers. And it says on the container it’s a skin irritant. See picture of a white kitchen towel that I touched the surface with. And this is three days after painting. Not really suitable for my purposes. I will try a different shielding paint. You can get types that do dry completely to a sealed surface, this isn’t like that.

I used this product to completely revive two tv remote controls that no longer worked properly. On one of them, the power button no longer worked, on the other there were other buttons that were dead. All you need to do is carefully dismantle the remote, and then use a cotton bud to paint some of the liquid onto the black underside of the rubber buttons of the remote. It dries within a minute. Then reassemble and the remote works again. It can also be used on rubber keypads that rely on conducting keys. Truly a great, versatile product.

Me get be my fault with regards to application (I only did one coat which covered the cavity walls) but when dry it’s really dusty and when fitting switch your fingers end up covered in black dust. Obviously this dust is conductive so now I’m trying to diagnose and suss a reoccurring switch issue, which may be due to the dust getting into the switch

The paint quality is okay and dries quickly, but it might not be suitable for all purposes, as the paint is not durable enough for my needs because it doesn't stick for long. However, it is still good for most of the intended purposes. The bottle has enough paint to apply if it comes off. I also tested it on a TV remote, and it worked fine on the rubber one but did not properly stick on plastic.

Super Product for Repair to your Faulty Remote Controls.. Thank You..

Good for small electrical repairs such as worn pads - be aware that it has high resistance so it it won't work to repair long traces. Dries quickly.

This product is absolutely useless as a conductivity shielding paint it does not do what it says and I am an electrical engineer and I've used many similar products that have worked. If you are looking to use this item for shielding a guitar body, I can only recommend copper foil with a conductive backing and perhaps even tip soldering copper sections.

Die Infrarot-Fernbedienung an meinem alten Samsung-Gerät reagierte anfangs nur schlecht, am Ende gar nicht mehr. Ich habe sie zerlegt, die Kontakte auf der Platine mit Isopropanol gereinigt und dann die entsprechenden Gummikontakte mit einem Wattestäbchen mit dieser Farbe bestrichen. Nach ca. 30 Minuten Trockenzeit wieder zusammen gebaut und siehe da: das Ding funktioniert wieder wie neu. Bin schon ganz schön begeistert das es vor allem so einfach war.

Terrible product, applied on a guitar electronic cavity using instructions, have let it dry for over 24 hours and the product stains everywhere making impossible to install electronics. UPDATE: the paint also provided grounding issues when electronics installed. Had to sand most of it off to resolve. NOT RECOMMENDED

Werkt perfect om kleine reparaties aan printplaten te verrichten. Bijvoorbeeld door waterschade of lekkende batterijen. De sporen kunnen eenvoudig opgeschuurd worden en gerepareerd met deze geleidende lak. Zorg voor een heel klein kwastje!

Worked perfectly to repair a keyboard with keys that weren’t working.

Excellent produit sans prétention. Non, ça ne remplace pas une vraie piste cuivre sur de grandes distances, mais sur de courtes ou modérées distances, pour des courants faibles, sur un contact souple de télécommande, ça marche très bien et facilement. Le fait que le solvant soit de l'eau, que ça sèche rapidement, que ça puisse se passer au pinceau fin ou au rotring ou à la plume en font un produit génial et très économique, avec lavage à l' eau des instruments