PC ProductsPC-Clear Epoxy Adhesive Liquid, 16oz in Two Bottles, Clear 70161

The product works well. No surprises..The stopper or lid/cap that holds the liquid mixtures in is well designed and comes on and off easily. You don’t have to cut the tips and deal with annoying snap-on caps/lids. The lid/cap simply twists on and off. I’ve used the product four times already removing and putting back the lid/cap. No mess and the cap/lid works and comes on and off without issues..The plunger is smooth and trouble free..The two liquids come out clear and transparent, but turn slightly opaque when mixed. The epoxy mixes into a liquid consistency similar to chocolate syrup rather than tomato catsup, so viscosity is not that thick, so it will run. I recommend using a tray to mix. I used a piece of cardboard and experienced some running..When applying, note that the epoxy is lesser in terms of viscosity. It will run off your scraper and spill, so take care. But spillage is easy to clean with a wet paper towel..Don’t over-apply. Just make sure you can get even costing on both aurfaces/sides of the materials to be bonded..No nasty odors..A couple of minutes after application, the epoxy feels sticky and rubbery, but that goes away and the material will turn rock hard after an hour or so. Epoxy dries clear. Hardly noticeable even after applied on a wooden door that is painted white..Very good bonding. I used masking tape to clamp/hold the glued pieces together. And the tape came off easily after curing/hardening..I would most definitely buy this product again.

I have used this several times to repair broken china pieces and pottery/stoneware pieces. I have been quite happy with the results and the items I have used it on have stayed together.

The glue works well and is strong BUT the glue dispenser does NOT dispense the glue evenly! It is supposed to be equal parts but it is not a good dispenser for this

If used properly, this stuff makes an incredibly strong bond. I used it to attach a copper pipe to an aluminum pipe on a DIY project. I realized that I needed to make changes and get the copper pipe off. Nope I broke the copper before I could get it to budge, Which I then had to hack saw it up and break parts off with pliers to get the copper off so I can re do it. As an adhesive, thats pretty much a 10/10. My intent was ot make my 2 pipes one, and this did that pretty perfectly.If you use this wrong the bond wont be great, but used well its amazing. Bonding 2 flat surfaces together isnt nearly as good. If you rough the surfaces up it helps, but all it needs is for one edge to cope up a tiny bit and it can be popped off. But if its a 3 dimensional joint, so that theres adhesive stopping it from moving being able to pull off, its amazing. When properly used, everything I try to take off breaks before the epoxy goes. So as a permanent solution I couldn't ask for more.And for ease of use, its very easy to use. I just squeeze a bit onto a piece of cardboard with packing tape on it to make a water resistant surface. Mix them with a paper clip. Apply it. Wait. Note that a hot environment will set faster.Try not to get it on your hands, its sticky and doesnt come off well, even with dish soap. But its not like super glue so it wont just instantly stick your skin together. so it gets points over glue for that.Also this is incredibly cheap and non toxic when cured. Meaning it should be safe for most applications. I cant really ask for more.

Great because:Cap can only go on one way, easy twist off, easy onDoes not set up in the tube or at the capsVery easy to extract, both components have low viscosityEasy to mix because of the low viscosityThe only caveat is that it actually has about a 30 minute working time and takes at least 3 hours to set up so the parts need to be clamped or some other method to keep them together. Also since both parts are almost clear it is hard to see if you have mixed them thoroughly. Take you time and mix them well. I am fairly sure that is why some of the reviews are poor and mention poor adhesion. The first time I used it I had the same problem and then realized it had not be mixed well.

I tried Kintsugi for the first time.I used this exopy and eye candy mica powder: Kula Gold.https://www.amazon.com/gp/aw/d/B088QT1BS6?psc=1&ref=ppx_pop_mob_b_asin_titleAn art scalpel is useful to remove areas where it smudged. It dries clear. It becomes one with the glitter. If you cut or file it down, the epoxy appears dull. (I suspect that is the same with all epoxy.) I liked the dry time. Pieces suck together when I put them together - I didn't need to hold it very long at all. However, I learned it was better to work in small batches so that it would apply easier- it would get much thicker after a minute or two. It is easy to do a little at a time because the screw cap works like a dream - brilliant. If I were to do it again, I would do it one line at a time and let it dry completely each time. I had some perfect lines and it had set enough to stick together. But when I pushed the next piece on, my other line came apart and I had to redo it. Not the epoxy's fault, I just wasn't familiar with it. After half an hour the whole thing felt really sturdy. I am quite pleased with it and I'm excited to use this exopy on other projects as well.

Works great

Fantastic glue for all those broken objects around the house. Used it on ceramics, glass, metal, wood and anything else that needs it. Easy to dispense the right amount, mix it up and you're ready to go. Make sure you give it some time to cure - it's not superglue but a super glue :-)

Muy buena aunque es muy poco precisa. Huele muy mal pero supongo que es por la resina.

Excelente epóxico, de verdad que sí pega el cristal, ya lo utilice en el cristal de mi comedor y de verdad que sí resiste..

good sturdy extruder

Very good epoxy but heads up - this is an insert that is to be used with an dispensing gun. It's not very clear from the description so I didn't realize. Managed to make it work for me though.