POE Combiner Splitter Adapter, Run 2 IP Cameras on 1 Cable, Works on all POE Switches, POE NVR and POE Cameras, Mode A and B POE Compatible

I had a buried line running in conduit to a tree for a camera and realized, I could eliminate 2 others from my house if I had another one in the same tree....IPCamPower to the rescue! Worth the money vs. time/effort to run another line. Initially, only 1 of the ports was active, but flipping the switch for that port fixed it. I'm assuming my cables are not as expected. I was VERY happy when it worked. I highly recommend it. It seems well-built and the instructions are fine...really, plug it in and go. If something is not working, try flipping switches (1 thing at a time, also make sure the cable you're using works, etc..). I had a bit of a tough time cramming all of the cables and the adapter into the junction box. I could have left it all out in the weather using the included caps. I'm very pleased. I see no loss of signal over the 2 cameras now running over the 1 cable. Power is good. I didn't measure anything but the video is perfect from both cameras. I'm running an 8MP and 5MP Foscam camera with no problems.

This does eactly what it says it will do and worked without touching the POE type switch while using it on a Ubiquiti poe device. It's not great with pre-terminated cables if you want to use the "waterproof" connectors. I would not consider them capable of keeping water out but this will definitely help you run two cameras as 10/100 with a single POE cable (of course you'll use up two poe ports on your switch). Would recommend if you can't run a dedicated ethernet line and need two devices that don't need gigabit.

Works great with Hikvision

I've been wanting to add another POE camera to my Reolink NVR system, but have been putting it off because of the hassle of running another 50ft (at least) Cat6 cable from the outside into my attic and then down the wall to the NVR. I didn't know these existed, but as soon as I found out, I had to try it. I have a camera in one corner of my house and wanted to add another one facing the other direction and this allowed me to do it very easily. Just plug in the splitter end (the one with the switches on it) into 2 ports on the NVR, plug in the existing single Cat6 cable that was going to 1 port into that and then take the other combiner cable out to where your existing camera is and hook in a second camera to it. Done! The biggest hassle is having to try and hide the extra cabling on the outside, but I wasn't too bothered by that. I'm just glad I didn't have to try and run another cable into my very small attic space to add another camera. Time will tell if it continues to work, I suppose, but so far so good. I'm happy.

It works, but I would have changed a few things... thing 1, the waterproof connectors are junk. I've done plenty of outdoor POE camera installs and there are connectors that work, and connectors that don't. These don't. I always use dielectric grease in the plugs to help with moisture resistance and even though I did that, I had this unit out for one day. One day! And rain came, water got in, and some of the cheap contacts in there rusted out. Probably shorted the POE if I had to guess (no damage to the switch though, a good POE switch knows when that happens and cuts off power). Thing 2, rather than having RJ-45 sockets on the output side, I would have preferred RJ-45 plugs. That's just me, so maybe there should be an option. As it is, for my install I had two cameras right there on a pole, basically facing forward and backward. So to use this, I had to grab a couple short cables to stick in between which just means even more watertight connectors to deal with, etc. When I had my water ingress and rusted pin, I just got done snipping off that particular socket (I think it was camera 1). I tested which color wires went to which pins so I could just wire it up to a new RJ-45 plug, which is currently working okay, and now I've avoided one extra ethernet cable on my setup. However, there's precious little slack on those wires where it splits out, so there's no way I could get a waterproof connector on. I'll have to stick with electrical tape and the aforementioned dielectric grease. Plus it helps to position the connection in a way that gravity will not let water pool into the socket itself. For anyone else who might need to rewire this... I didn't cut off the pigtail going to the 2nd camera, but at least on the first one (and you know which one is #1 because it's using pins 1,2,3 and 6 ... the other one uses 4,5,7,8), the wire colors are: #1 = white, #2 = yellow, #3 = black, and #6 = red. Wire those to an RJ-45 plug and you can do it too. Bear in mind, these wires in there are kind of cheap stranded wires, so good luck pushing it into your RJ-45. I tried and tried... eventually I had to strip back just a little bit of the wire itself and tin it with fresh solder, and that lets you push it into the plug and crimp it. It's also a pain in the neck to wire when you're only dealing with 4... pushing in all 8 wires is pretty easy because you just line them up and go. With 4, and using 1,2,3,6, it's kind of tricky to get it just right, so it takes some time and patience. Now, I figure I could have returned this since it's literally 2 days old and already rusted and broken, but I can't say for sure if the water issue was my fault or the crummy waterproof connector, so I sucked it up and fixed it on my own. For all the other connections, I made sure to use generous electrical tape now on all those joints. I figure water just got in past the rubber grommet where the wire goes in, because it's not really that tight, so taping it there to prevent water from getting there in the first place helps. I've done that in other spots where the connector seemed dubious. Time will tell if it all holds.

Perfect for ip cameras save a lot of time

The concept is good haven’t tested the quality yet but there are two major design flaws with the waterproof caps which makes it useless for my project 1. The rubber gasket is not split so impossible to fit around a finished wire, which makes it completely useless for me. 2. The end cap that you would screw on to the prong end the diameter is way to small which makes it physically impossible to use with a finished RJ45. making the waterproof concept completely worthless for me to use. This company’s product department must revisit their design flaws as it prevents the concept of a waterproof/ water resistant system. Picture a picture speaks 1000 words pictures attached to demonstrate their product versus industry standard. Really wanted to love the system however without manipulating a $20 set you would like you shouldn’t have to cut widen the caps for it to work. One would think this should have been thoroughly thought through but it wasn’t. The end of the RJ45. Don’t even match the identical version that I have which has the rubber coverings for the plastic clip. I really needed and wanted this to work, as I had to finish my project today. Its now not going to happen as it can’t work for my outside POE system. I would not recommend this to anyone wanting to waterproof/water resistant their system.

Works well easy setup

I hadn't heard of devices like this "IPCamPower POE Splitter Kit" before. I've recently upgraded from an 8 channel NVR (using POE), to a 16 channel NVR with POE. The only down side to that upgrade is running the cabling for the extra cameras. I bought this kit hoping it would work, and the good news is it does perfectly. You plug the splitter/ combiner? (with the switches on it) into the two channels on the NVR you want to use, then run the single cable from it. Then plug the other splitter cable onto the end of that single cable. Then run the two cables to your cameras. I used B mode on the combiner end as suggested in the instructions. After the splitter at the camera end, I've got one camera on a 5m cable and the other on an 8M cable- they work fine, even the POE.

شغال ممتاز

Potwierdzam, że działa z kamerami i rejestratorami Zintronic / Herospeed. Zwykłe rozdzielacze nie działały.

Been using this for a month now powering my Reolink doorbell and IP camera works well so far.

Purchased for our home security cameras. I had no prior background with installations and found these were easy to set up! We have 4K cameras - the video/image quality appears unchanged when using these. Perfect for what they are for!