PIR Sensor Outdoor IP65 Wall Surface-mounted 12m/180° + 3m/360°

Great bit of kit, I’ve mounted this on an oak porch connected to a huge carriage lantern and it works perfectly! The sensor activates the lantern from the end of the drive which I set up with ease. The whole connectivity, wiring and installation was straight forward and surprisingly easy for an amateur like me. It has been up now for few months through all sorts of extreme bad weather wet, dry, hot or cold and still works fine. Great value for money and would highly recommend.

This is a very good PIR detector, with 1 star knocked off because there is no detection sensitivity setting - there is only the option (via the setting dials) to change time on, from a minimum of 10 seconds, and the light level sensitivity (day to night). I have it fitted to the underside of the soffit boards of a low roof, and facing the prevailing weather. The ability to mount it with the wires coming out of the top was very useful for me, and so far it has stood up to some extremely rainy days. I have it mounted facing the front gate which is about 4 metres from the road, and because of the lack of ability to set the detection sensitivity I have it pointed down at quite an angle to avoid being set off by passing cars the whole time. This negates the secondary PIR sensor on the bottom of the unit, but with a bit of trial and error I got it detect anyone coming through the gate, and also cars that stop by the front gate. Side to side range remains very good however, and it detects anyone leaving the front door about 5 m to the side. I don't have it set up to directly control a floodlight that I put right next to it - I have the PIR output connected to a switch input of a Shelly 2PM Gen 4 relay that then connects to Home Assistant, and have the light setting set to so that it detects motion at all times of day and night. That way I use it to tell me when someone comes through the gate - it's surprising how many couriers don't knock on the door very loudly and end up leaving because we have not heard them. To work with the Shelly device, I needed to connect a highish value (~330Kohm) 2W resistor between the L' of the detector and the switch input of the Shelly - as instructed by Shelly themselves - and having done this, it works perfectly. That said, I have programmed the Shelly to switch the floodlight on and off independently of Home Assistant, i.e. with local logic, and to do this between sunset and sunrise only. Overly complicated? Maybe, but it gives me a lot more control over the light than is possible with a direct connection of it to the PIR sensor.

This item is from a German company but made in China. Having said that the build quality is very high and the item works very well. An excellent instruction booklet is provided which is split into sections of many language’s. The unit is well sealed against water ingress and easy to fit on a flat surface. The unit has two separate pir sensors the longer range one is adjustable up and down but not side to side, the other close up sensor is mounted under the long range sensor. Because the long range sensor does not move side to side it’s horizontal adjustment appears fixed, but can be adjusted. To achieve this individual elements of the pir lens can be covered with white sticky tape, which stops them working. The adjustment of the operating area is by a walk test in daylight, set the lux control to Sun and the time control to 10s. With the unit powered up walk the area covered by the sensor to see where it operates and adjust as required. When you are happy reset the lux to how dark you want it to operate at and the time control to the time you want it to operate for. Job done.

I have just installed this and am very impressed by the quality, which is comparable to a much more expensive one I bought previously. Solid german engineering, everything fits well, and waterproofing details seem well thought out and good. Early days so I can't comment on durability, but it was simple to install, and works perfectly. Adjustments are clear and well calibrated, as opposed to others I have used. I was fed up of having to replace sensors every couple of years or so, and went for this for its IP65 rating, which is about as good as you can get in terms of water ingress protection. Very pleased so far. Update 12 months on - has worked perfectly, sensitivity is just right, and reliable. Very impressed, and will be buying again for an installation I'm doing for my daughter.

The product works well now it’s installed but a couple of things need to be taken into account when fitting it. Firstly it needs twin and earth flat cable to properly fit into the electrical connector inside the sensor. My lamp cable would not fit so I had to connect the lamp cable to the electrical cable to allow it to fit. Fortunately there was enough space to allow that. More problematic is the size of screws which connect the backplate to the sensor itself. They are very small and almost impossible to screw into the small holes. Bear in mind I was up a ladder trying to fit screws only a couple of millimetres long into it. I eventually fitted slightly larger screws which allowed me to finish the installation.

Excellent Pir, very easy to set up. Much better than some others has 2 Pir's one face forwarding which you can adjust to your preferred motion detection zone and one that points directly down to ensure anyone standing below the Pir will be detected. Which means if its placed directly above your external door the light comes on as soon as you move into the door way, no more walking in the dark for the first few steps.

This works very well but my husband found it rather fiddly to install in place of the failed one, although that was of a different design. I think we need to tinker with the range a bit but we are pleased with it overall.

This has replaced a neighbours PIR sensor that failed and has a bonus that there are 2 IR sensors so that the dead area directly below the sensor has been removed. The wiring / terminal box is ok for standard single lamp connection but to connect a secondary remote lamp made connection very tight in this instance. The range is very good and easily 15mtr to the end of the neighbour's drive (surprised me when it picked me up opening the gates whereas the original never did. Has worked well since installed and neighbour very happy

Come oggetto si presenta bene sembra di qualita' molto bello nero e come aspetto , un po' diverso dai soliti . Semplice come montaggio al momento funziona bene , si vedra' nel tempo .

The sensor is quite good quality, however don't expect to have detection range at 12 meter as it is mentioned in the description. The range however is approximately 8 meters maximum.

Great product works great looks 100%

Détecteur petit, discret et très efficace. La portée de détection est comme dans la description, 12m. L'appareil est petit et donc discret mais tout aussi performant. Notice suffisamment claire, pas de soucis d'installation. Il est très sensible aux mouvements. De plus la durée d'éclairage est réglable. Chez moi, ce détecteur ommande des lampes LED, c'est parfait. La qualité y est, bien conçu. L'étanchéité devrait être parfaite, tout est prévu pour empêcher l'eau d'y entrer. De part sa petitesse, c'est un peu serré pour y cacher tous les fils mais facilement faisable. Attention à bien respecter la polarité. Si la polarité n'est pas respectée, il ne fonctionne pas mais surtout cela ne l'endommage pas.

✅ LO MEJOR: • Buena detección de movimiento. ❌ LO PEOR: • No le encuentro pegas. EXPERIENCIA PERSONAL: He instalado este detector de movimiento en la entrada a casa, porque no quiero dejar la luz encendida cuando salgo a pasear a las perras en la noche y no veo ni torta para abrir la puerta. El sensor frontal detecta 180° y el inferior 360°. En mi caso, podía optar colocarlo en la luz del techo o en el aplique. Queda totalmente escondido en el aplique, visto desde fuera, logro que solo detecte un metro antes de la puerta y que no detecte a nadie que pase por la acera porque con el mismo aplique corto el campo visual y lo ajusto a lo que yo quiero. Se puede ajustar la oscuridad necesaria a la que el detector funcionará y el tiempo de encendido, desde 10 segundos hasta 15 minutos. La conexión es sencilla, si entiendes lo básico de electricidad. Y como una imagen vale más que mil palabras y un vídeo más que las imágenes, os dejo un video y un par de fotos, para que veáis que tal son los sensores de movimiento. Si esta información te ha ayudado a decidirte, ya ha servido de algo mi ayuda. Muchas gracias. :-)