Motor Control Board Controller Easy Installation 430157 Works with Nordic-Track S22I S15I Stationary Bike

Got the bike for free, diagnosed this part was faulty. Found cheat mode so don't have to pay subscription charges which will pay for this part. Apparently a known fault on these over-engineered bikes.

S22i from Nordic Track stopped working. After exhausting all inquiries with the company we decided to order this. It worked!!! Worth the money and the time it took to install. Google some install videos if you need help.

I was very nervous about purchasing this product because the circuit board did not look exactly like the one on the S22i. It had one extra component on the bottom left side. However, Nordic track was going to charge as much as this replacement part just to diagnose the issue, and I would be required to pay upfront before the technician ever arrived. That just didn’t make any sense to me.This part worked perfectly. Taking the bike apart is the hardest part (watch YouTube, and know that you’re going to have to have some brute force on some of the screws and pedal removal), but the switch-out of the circuit board was easy. I recommend taking a picture of the previous one before installing the new one so you can remember exactly where to connect the wires and when you remove the screws to take the rest of the bike apart, place it in the location on the floor adjacent to where you’re going to have to put it back. There are a lot of screws in hidden places. Oh, and you have to take the screws out on both sides before the plastic cover will come apart. It took me a few minutes to figure that out.And don’t be impatient. It takes the bike a few minutes to completely cycle on the first time around, but the screen came on immediately.I cannot be happier with this purchase!

Finally found the piece I needed and worked

Purchased bike in 2020. Didn't realize you are not supposed to leave power to it. The monitor stopped working, fan not working, nothing worked, it was dead in 2023. Found a video online on how to replace the circuit board that is hidden behind the chain guard. Bought the board it fixed the problem, everything works again.Replacement was fairly simple, watch the online video. For my bike, start by taking off the left side pedal, it is easy. You need a 5mm Allen wrench to loosen the bigger bolts, then you need a 3mm Allen wrench to remove the special bolt that actually holds the pedal on. You take off the left side chain guard cover sheet metal screws using a Phillips screw driver, go around to the right side and remove the rest of them, remove the small circular plastic guard caps up front from each side (there is one sheet metal screw and one threaded screw meant for a threaded hole, keep them straight), then pull off the left hand chain guard cover to expose the circuit card, I left the right side guard hanging on, no reason to fully remove it. Now pull off the circuit card electrical clips (they are all different, no chance of mixing them up later), you have to pry the little plastic lock arm so the clips pull out, remove the circuit card threaded screws (they are small, don't lose them), and take out the circuit card. Put in the new card by reversing the process. The tiny circuit card bolts are a pain to get back in, a magnetic Phillips screwdriver would help, I wound up carefully tipping the bike on its side being careful NOT to support the bike on the monitor, and used gravity to help get those pesky bolts back in. I used a small piece of masking tape to keep the bolts stuck to the Phillips screwdriver driver until I got them started in the hole, then I pulled the tape off. Put the covers back on, put the pedal back on, you are done. 20-30 minutes.

It was a bit of a guess but replacing this part was about the same price as getting a service guy to come look at my S22i. It would take two visits to fix my machine according to Nordictrack and just as others have said, this board is the solution for the black screen of death.

Arrived quickly <1week. Wrapped in bubble wrap in a small box.My Nordictrack S22i stopped working. Admittedly, I was not turning the bike off daily, but that seems like poor design. I looked online and saw replacing this part could solve my issues. It did! Was easy to replace, I watched a tutorial on YouTube. This part was the same brand as the one inside the bike. I also ordered a plug with remote so I can turn the bike off more easily.

I replaced the board in my NordicTrack and this fixed my dead screen issue. Board is located on the left side under the pedal assembly. The only pain was disassembly of the belt guard to get to the board.