Spartan Mounts for Mag Wall Display - Firearm Accessories, Wall Mount Display for Gun Room, Magazine and Ammo Storage and Organization, Black

Does the job as intended.I have 3 of hangers for the pmags.Its American made & comes with the hardware to install it. What more can you ask for.

I would like these to be a little better. When I load three (loaded mags) it sags even though it was installed correctly.

I missed it in the description but this is in fact 3D printed. Nice mount that is worth the price. Mags fit perfectly.

I saw the other review that said total garbage and I ignored it. I purchased it anyway thinking there is nothing to it. What could be garbage?Long story short, I am glad I did. It isn't fancy there is no shiny chrome, but it is functional which is about all I care about. It is a 3D printed PMAG holder. I can't stress that enough so I will say it again. It is a PMAG 5.56 holder, not just any magazine will work with this. IT IS FOR THE BRAND PMAG .223/5.56!Now that that is out of the way lets talk about the picture shown. If you hang the mags as shown with the curve to the wall it will not sit right unless your wall mount is screwed to a 3/4-1" board. If you spin them around so the curve is out they sit nicely in the holder. Another 3/4" of molding behind them would make it work either way. (Suggestion for the Manufacturer) That is the reason for the 4 stars vs 5 stars. Also minor side note: there was one minor sharp edge I fixed with my pocket knife.I am sure someone will read the above and say something like if you hang them curve out the bullet is facing the room, that is dangerous. I am about as worried about that as I am worried about my gun getting up and going on a shooting rampage on its own. If anything it is probably safer because the primer is not available to be struck by something hitting it. With that said, I don't leave all my mags loaded so it doesn't matter. It is hard on the springs to leave them loaded. Buy a quality speed loader and you won't either :) Leaving 1 loaded to protect your house and family only seems paranoid until you have to use it, then it just seemed smart.I don't need to add a disclaimer as I don't work for them, didn't get any discounts, wasn't paid to write a review, and don't have to be to be a satisfied customer.Update (4/21/2018): I upgraded my rating from 4 stars to 5 stars and here is why. I just moved my mount to a new location and realized I was a little hard on them about the angle. There is a light angle on the back of it when I initially installed it apparently I over-tightened it and it pulled that into the sheet rock some lessening the angle. On my remount I was a little more careful and it seems to be a tad bit better. You can hang a mag as shown, it isn't perfect, but its better than before.

This is the only AR-10 wall-mount magazine rack I could find, and it’s a great product. It’s 3D printed, very lightweight and sturdy. I mounted them to the inside walls of my safe.

Just as advertised. Good price

These are a perfect fit for Magpul P mags. This mounting system needs an extruded lip on the bottom of the magazine in order to catch them this is not compatible with USGI magazines. The install is straightforward and the screws and wall anchors that they provide seem to be sufficient although I did not use those as the depth of the wood inside my safe would not allow me to use the length of those screws. I gave the value for money four stars because it seem to be a bit pricey for 1/2 of the price I would’ve bought four but at the current price point, it leaves me second-guessing whether I even should buy a second one. In Spartan's defense I don’t know what the machines cost to print these. So this may be a moot point. All of that aside I thoroughly do like the way aesthetically and functionally that it removes loose magazines and aligns them in a proper fashion. I would like to see differentiating colors to separate ball from personal defense rounds or even if you wanted to separate different grains or calibers. For what it is worth my x6 mags fully filled weigh in at 7 pounds 8.5 ounces. With my 5/8 wood in my safe the 1.25 inch wood screws work excellent. Again, sorry for the photo rotation...( ask Amazon)

MPX version was probably designed for MPX Lancer Mags, item does not work with latest SIG MPX 35rd mags.