D-Line 13.12ft Cord Hider Kit, Patented Cable Cover, Hide Wires on Wall, Channel for TV Mount Cords, Raceway Wire Hiders, Paintable, Adhesive, Half Round, 4X 1.18in W x 0.59in H x 39in Lengths, Beige

Well made and easy to use and install.Attractive and blends in with the white molding or can be painted to match.Highly recommended

Easy to put on! Just a reminder, the connection parts are better to put on before you tape all the tubes. Also, it is really easy to cut, because I use my kitchen knife lol

I purchased this for the power cable of our baby monitor, which runs vertically from an outlet near the floor up to the monitor, which is about 6' above the floor. I wanted it partly to make the stark white power cord less of an eyesore, and partly to prevent my son from grabbing the cord or playing with it. This product worked perfectly.Fortunately we had some paint left over after painting the nursery, so I was able to use that to paint one of these channels and make it less of an eyesore. As another reviewer suggested, I sanded the channel first with some 200-grit sandpaper. It's visible on the wall, but not something you notice, and it certainly looks a lot better than the dangling white cord did!The adhesive seems to be holding fine so far to the painted drywall. Inserting the power cord was easy, as the whole channel sort of swings open.

The half-round profile blends in with baseboards very nicely, if you happen to need them there. If you were looking at them from a distance, they could both appear as a single, original moulding.When looking through reviews, there seemed to be a mix of people saying the adhesive was either too strong or a bit weak.I considered using some known 3M adhesives to sidestep either issue. However, I had completely forgotten about this until I had already started installing them. The units I received definitely had very strong adhesives, to the extent that they will certainly remove paint should they need to be removed.In our case, they are being run along the top of baseboards and this strength is far preferable anyway. This is in an area where there is a lot of movement and anything not strong would be worse long-term and there is no intention to move them around. Worse case scenario, touch-ups are not hard to do. However, if one may not be entirely sure about placement; it would be advisable to use a known, non-damaging adhesive temporarily or permanently.So far, I’ve not made use of the connector bits. Instead of using the straight couplers, I just left small gaps for future access. I only had one corner in the installation, but did not want to bend the coax cable enough to use the 90° coupler. The looks in these spots were not of concern anyway.I can see how these pieces would be cause for frustration if you are planning to need them, though. They fit loose and feel like they would easily come off. Was not a concern for us though.I’d buy again if needed.

Used these to hide wires for picture lights. Worked great - held 3 cables and matched the wall color well. Easy to attach.

These are the easiest to work with! They are well made and easy to configure and install. I wish the corners fit together but I found a solution for that. You can cut the long pieces with a scissor making for a clean cut. Used similar kits before but I truly like this one the best. Easy, peasy, great!

Does the job, with some limitations:There is printing on the inside of the tracks with manufacture information, 4/5 of it is advertising the manufacturer, the remainder looks like a date. No safety information like material or temperature rating which could be useful. Waste of ink and, unfortunately, they took no effort to ensure the printing did not go all the way to the edge . Three of the four rods had printing right to the edge and my particular installation had a few eye-level installs and looks really bad. The useless printing would be better served on the removable film from the front or the tape on the back.The tape itself seems ok but it's very thick and this prevents a true wall-flush install and kind of accentuates a shadow behind it. I did use the tape but if I were to do it again I'd probably just try to dissolve the tape off and staple the covers directly to the wall through the soft plastic.Last complaint are the corner covers. It's very very thin cheap material and very finicky to attach and remove from the rails. They do an ok job but I don't think they'd survive an accidental boot or runaway rolling chair. Considering these covers are serviceable by opening, I'm a little dubious at how much servicing I'll be able to do before these corner covers fail. Some of the edges also had some flashing that I had to remove as if it were a model kit, and since the kit itself is kind of stingy with the number of these corner covers I found it fairly annoying.It's a bit of a shame because having a cord cover that can be installed without disconnecting any cabling, and cables changed after install, is pretty killer. These were quite a bit more expensive than the alternatives and I don't feel that extra cost really went into the product care and quality.

I bought two packs of these to use in my garage to conceal the wiring for my garage door opener. Of the 7 of these that I used, only two of them had an issue with sticking initially. Eventually I was able to get them to stick and they haven't come back off YET, but the others stuck just fine on the first try. This product comes with a good amount of parts to attach the rails to each other, and there was only one angle that I needed that wasn't included, which was going from the top of the wall running horizontally to the ceiling. Other than that, this is an awesome product and has made my garage look way nicer.