Combines 3 shapes of resin art molds including Round, Square, Pentagon Shaped. You will have a lot of fun casting your own crafts by using these silicone molds for resin. Enjoy DIY The silicone resin molds are compatible with most resins or other casting materials such as epoxy resin, polyester resins, polymer clay etc. You can add some resin pigment, resin dye and embed different kinds of embellishments or fillers, create your resin art projects such as the flower pot, pen holder, succulent planter pot etc. Storage and Care Please store your resin molds in room temperature place, avoid from the direct sunlight. Clean these epoxy resin molds with soap water;for the finished products, there will also be rough edges that will need to be sanded and polished once removed from the mold but do not sand until the casting has fully hardened. Warm Tips for DIY Resin Crafts (1)How to make: Pour resin into measurement cup, slowly stir to release bubbles. Adding glitter or pigment into it if you need. Then pour it into your mold and slowly stir. Allow to stand for 24 hours and take it out. (2)How to clean: Please clean the resin casting molds with clean water or rubbing alcohol before use, then use a soft cloth to wipe clean. (3)How to store: Please store the resin mold away from direct sunlight and dust. (4)How to de-mold: You can use a mold release spray and let it dry in the mold. If you don't have, you may need a baby wipe or a drop of soap mix with a bit of water as a release agent, work it down to the mold, then push the project from the bottom. Please make sure your resin piece is fully cured when you decide to de-mold.
J**R
Get the two small ones. Don't bother with the big one.
So I wish I could rate these molds seperatly. The two smaller silicone molds are wonderful and I have no issues with them. I would buy those again.The larger mold.. That's a different story. I finally got around to using it as it has some operational issues from the get go. The whole thing is made out of hard plastic with a thin silicone sleeve that I guess is to make it pop out easily but very clearly does not work. The top stretches over the sides of the plastic but pops off with just the force of the resin. I fixed this by hot gluing the top down on the edges which works fine and peels right off after. But after you have let your mold set there is literally no way to demold it. Not enough rubber stands out to pop it out of the hard plastic. There are little holes in the bottom so you can push it out I think but there is no way to hold the sides of the mold and push in the holes to help it pop out as there is no where to put your hands that does not hold it in place in the mold. I also tried the typical demolding a stuck mold options like freezing it for a while. Nothing worked. After several hours trying to get the resin out I ended up cutting the hard plastic and ripping chuncks off to get enough of a hold to pull it out. So a one time use mold.Also the shape is really weird. It's balancing on this tiny little square and is super easy to tip over. And you have to go that full on the mold or the cavity will be open at the bottom. Overall a very poor mold design and I won't be getting it again..The pictures are from when I just got it out of the mold and I have not yet gotten the extra resin seam off from where the top meets the base.
M**Y
Love the look, would change a few things.
I use my molds for cement work, and this is one of my favorites. The only issue I’ve had is leakage, which I fix by taping the edges shut before pouring. I do wish the inside of the mold was shallower and not rounded- I made a few by pouring without the lid to make a wider flat base, but then there is no bottom, just a “tunnel” that I have to patch with a second pour.
E**Y
Ok
Bought for resin. Second use the square on got stuck but I’m still able to use. The one that’s odd shaped leaks everywhere so I won’t be using it again
T**S
Not bad 5/10
Honestly I don’t know how to use the plant one but the other ones are perfect to use
N**
Leaked & broke
I have only tried the larger mold for a flower pot. And it is a good size but it leaked everywhere and now it’s broke. So I will attempt the smaller one and see how that holds up
D**D
Does the job!
Love these little molds! A little trickier to de-mold but nothing a little soap and water can't help.
O**O
Moldes Silicola
The media could not be loaded. Excelente, al cuadrado le falta un poco mas de rigidez, pero el proyecto salio muy bien fácil, de desmoldar, limpiar y resiste muchos usos
A**R
Bigger mold doesn’t work at all and had to be thrown out
Only giving two stars because the two small cups work fine. But the mold for the planter, I could not get my project out and sadly it was a ton of wasted resin.
Trustpilot
5 days ago
3 weeks ago
