BIG RED T84032 Torin Hydraulic Low Profile Aluminum Racing Floor Jack with Dual Piston Quick Lift Pump, 3 Ton (6,000 lb) Capacity, Red

This jack is as advertised. Once setep this thing will have your car or truck off the ground and ready to work on in a couple of pumps. Very nice. So nice I bought two.

Poor quality made in China. Wheels did not roll correctly so we had to do some machine work just to get them to roll properly because of poor quality control and not enough clearance on side of wheels and the bore was not true. At first we machined .030 off of one wheel and .050 off of the other front wheel we were able to get them to at least roll as there was not enough side clearance so the factory just left the bolts loose because when tightened the wheels would bind. This helped but the bores were off. So we machined new bushings and bored the wheels to true them. Then we notice the swivel wheels have excessive clearance. This jack must have been made from the rejects of the JEGS Performance factory. Get the floor jack from JEGS Performance Product which is a great floor jack which is also China made but to higher standards.We build airplanes and know what quality is. This jack looks good in the picture but is a cheap jack that cost a bit.

I DIDNT EVEN TAKE IT OUT OF THE BOX , AFTER REREADING SPECKS THIS JACK IS ALMOST AS WIDE AS IT IS LONG , PLUS THERE IS NO REASON FOR A 3 TON JACK ALUMINUM TO WEIGH IN AT ALMOST 90LBS

The jack wont hold a car for 10 min horible quality its heavy and parts were missing from the handle

I bought this jack over all the other 3 ton jacks simply because it was labeled as a pro series and I thought it was a great looking jack. I liked the machined sides with the "PRO SERIES" milled in the recesses. A jack has one simple job and thats to lift items that weigh up to its lift rating, 3 tons is 3 tons so i went for looks and I regret that now. First thing I noticed when the jack arrived was its lowered height. On the box it states 4-1/8" lowered height while all the advertising I've read states 3-7/8" I know its only a quarter of an inch but its misadvertising just the same. Opening the box I noticed the jack isnt the same red as whats shown in all the torin adverisments and there are stickers in the recesses, not "PRO SERIES" as shown in their advertisments. Not a big deal but its noticeable. There are no bearings in the wheels and none of the wheels were even lubricated. When i moved the jack across the floor it made some impressive squealing that got my dogs attention!! Also, mine came pre scratched so i didnt have to worry about that dreaded first scratch!! You can see by the pics that the damage wasnt from shipping, that area was completely cover by styrofoam and couldnt have been made after the jack was placed in the shipping box. This means it was done prior and they shipped it anyway, again their quality is horrible! How they could ship an item that was clearly damaged speaks volumes about torin. I assemble the handle, removed the wire holding the jack mechanism down, lubricated all wheels and joints mentioned in the manual, then the air removal procedure. I stood on the lifting arm while I pumped the handle and it lifted me just fine, now mind you im only 200 lbs. So I'm not thrilled at this point but I need a floor jack for an upcoming job I have on my pickup and if this works well i wont bother sending it back. The day comes to use the jack for the first time. I confidently slide it under the axle of my truck, pump the handle quickly until it close to making contact then i take it slowly and start to lift the wheel up or so i thought. I keep pumping the handle but the wheel isnt moving. I figured the valve must be open so i rotate the handle to close it and try again, still nothing is happening. I assume the overload valve isnt set properly and thats why it wont lift approx 1,250 lbs, way below its rating. Now im super frustrated because I need the jack right now and I only have a certain amount of time to get my truck done. With everything considered i would stay away from Torin products. They have some pretty serious quality and advertising issues. The jack has one purpose and they dont even check that one thing before these are shipped to customers. Companies need to provide quality not junk, especially when we are spending more for a pro series and receiving a bargain basement item. Now I have to take time out of my day dealing with sending back a defective item, ridiculous!!