1.75mm Light Gray PLA | Engineering Gray (Light Grey pla,Cool Grey 6C, Warship Gray) 3D Printer Filament - FilaCube PLA 2 Cool Grey PLA Filament Blue-Gray [Made in USA] war Ship Light Grey pla+

Overall this filament is a solid 4 star in my book. What brought it down a notch for me was while the spool has even windings, they are too tight. Every print that I've done so far I noticed that the filament would tighten up, then suddenly jerk. I noticed this happening on either side of the spool and this did it consistently. This had me concerned as I felt at some point this is going to give some kind of printing error and sure enough during my 8th print, about the 1/2 way into a 12 hour print, there was a failure causing a layer seperation which i can only attribute to the very tight windings.Unfortunatly I wasnt there when this occured and I didnt notice the error in the print until it had finished, while I was removing it from it bed. Very disappointing to say the least. The other prints up to that point were flawless.I'm not an expert, but I'm not a novice either. I've been 3d printing for many years and I own 3 printers and this is the only time I have ever experienced this happening (the filament tightening then jerking causing layer seperation.) Some may think that there may have been an issue with the file causing the layer seperation, however all the previous prints came out fine and they were all the same type part, So this is the only conclusion I can come up with.The only other issue I have is with the color/name. This color is called "leather" which was the color I was hoping for, but I think that fell short a little. I will admit, it was close, but in my opinion it couldve been a tad darker. But "good enough" for what I needed in a "leather" color.Pros:-Made in America! And in the great state of Texas! I am so tired of stuff being farmed out to China!-Nice even windings-Prints like butter, prints come out silky smooth (I use Prusa Slicer on their finest setting. Very long print times but well worth it!)-Very minor, if any, stringing, pimplingCons:-Windings while are nice an even, are very tight causing the filament to tighten and then suddenly jerk especially as it spools out at either edge of the spool. To me, this is a Major zonk!-If you use Supports they leave the area light colored but with carefully applied heat to the effected area, it will return the original color back.Would I buy it again? Unfortunately because of the issue I experienced, I would have to say no. Which is a shame because up until the problem occurred I was really impressed with this filament, but I just don't want to chance this happening to me again. I'm hard pressed to even use up the rest of the remaining filament.I hope this review helped the 3d printing makers out there! "Keep calm and print on!" Lol.

Well made and consistent quality and color. Prints well and is made in the USA.

Prints good. Will print more stls that call for flesh tone filament.

If you're looking for a very light gray, this is pretty good.This PLA works very well in my Ender 3 V2. My machine is dialed perfectly and I use a flexible steel PEI coated build plate and a glue stick. Small parts don't unstick during a long. I printed 25 CHEP cubes (actually way more than 25 of various colors) as toys, and forcing the PLA to stick to the heated bed 50°C was needed.EDIT: My spool of ENGINEERING GRAY PLA-2 was terrible.. BAD.. Could not use it no matter what I tried. It continually jammed in the nozzle and the extruder motor/gear would build pressure, then skip/slip -CLUNK- , thousands of times during a print. No matter what settings I tried this one spool of ENGINEERING GRAY would not run. I switched straight over to several other spools of different PLA's, and prints would be fine! So the issue is this one spool. i have never had one so bad before and it is a shame. The cool gray works well.

This product is a cross between PLA and ABS. You have to turn the nozzle temp up a little more and the bed temp down or not on at all. I run 225 nozzle and 40 bed temp on a Creality Ender 3 Pro. I run the same on the Diggro Alpha-5. It was a little tricky to work with at first but their customer service gave me some advice and it worked. This product is stronger then PLA as well. So not only a highly recommended product, they also have quick customer service which is hard to find with filament manufacturers. A professional 3D modeler I bought files from told me about this product and I will never buy anything else now. It's worth every dime and you won't use as much as cheaper PLA filaments. So stop buying the cheap $12-$15 stuff and get this instead. You will not be disappointed.

I'll start by saying that FilaCube has my favorite gray filament and I use it religiously, so I didn't hesitate at all to order this one. Same brand, different color, same results - right? Nope. I couldn't get this to print to save my life on 2 different printers. The adhesion was nonexistent. I actually spent the better part of my day troubleshooting my machines thinking it was them until my wife reminded me of the new filament. As soon as I changed spools to test with the Inland brand, it was like magic and I no longer had issues. Prior to this, I've had positive experiences with this brand as I mentioned previously and I've been printing for years. Lesson learned with this one, unfortunately