Nova6006 Mini Cole Wood Lathe Chuck Jaw Set

Purchased for my G3 lite chuck, but the screws didn’t fasten and it was too big.

Lost one pie slice and had to buy the entire set- so for 3 luck wood turners I have spare parts - geeezzzzz - I have used these a lot and have bought the other "buttons" to fit different applications/shapes. Works well and fits my G3 chuck at slow light cuts. Recommend if you do buy these to tie them together to keep the spastic one from escaping - I will find it one day all down and out in the dark corner of my garage - but by that time no therapy on this world will be able to save it.

I love the fact that I bought my Nova chuck over twenty years ago (I think they only sold one model then and didn't even give it a model name), and just bought these Cole jaws and they fit and work perfectly. I like a company that doesn't keep changing something that works, and supports products it made in the past. There is an accessory set of soft buttons for these jaws which I'll probably get at some point, but for now the standard buttons are working fine. I'm using the chuck to hold wooden rings for sanding. I sand the outsides with the buttons gripping the ring from the inside, then switch positions and sand the insides with the buttons gripping the outside. It works great.

These Cole jaws are fine, but I do not use them as often as I expected to. Definitely buy the larger ones (12") if you are going to have only one set of these. These are nice for smaller work on a 10" lathe. In fact, if I were using only the 10" lathe, I would probably recommend these rather than the 12"

Technitool's mini cole jaw set is just about the perfect answer for finishing up the bottom of smaller bowls and other turnings. I was sorta surprised that the jaws were aluminum and not the 'traditional' polished steel that my other Technitool jaws are, but since they are 'outside' of the chuck's housing, I can see their reason for making them out of aluminum...less weight... I also ordered and received a complete set of spare screws and rubber stops just in case I loose or wear one out and also quite pleased with them. Now I need to order another chuck so it can be a 'dedicated' chuck for these nice little jaws... :>)

Take your bowl work to the next level. Make finishing and detailing your bowls a new experience. Well constructed and engineered. Mounts flawlessly to nova chucks. Only cons are: supplied fingers are a little short for any project with even a mildly rounded edge. Would consider purchasing 1 inch fingered. Secondly, really requires a second chuck... mounting involves break down of your working chuck to install... can be a little time consuming.

Upon receiving this cole jaw set I learned that like the other reviewer, they had sent the wrong screws for connecting the jaws to the chuck. Thankfull I had ordered a set of replacement screws for my other jaws and they came at the same time that the cole jaws came. These jaws work wonderfullyand have had no problems except for the previously mentioned screws. Hopefully Teknatool will read these reviews and correct this error. Depending on the curvature of the lip on your bowl, be sure not to over-tighten the jaws as this can cause the bowl to push away and slip out. I did this yesterday. After repositioning the bowl I was more careful and just snugged the jaws on the bowl and it turned just fine without slippage.

This was ideal for my small bowls. I have a midi-lathe, so this is the largest chuck I can reasonably use. Its nice to now have bottoms that are not an inch thick.Note: for those that don't read the instructions: the LONG screws are so you can mount the 50mm chuck jaws on TOP of the cole jaws. This allows you to have one configuration for turning the entire bowl, without having to change chuck jaws in between.

I am new to woodturning, nevertheless I found that NOVA line of products and this product in particular are of very good quality sold for very affordable price which is very important for those who just starting learning the trade.

El producto llegó antes de lo programado. Buena calidad de materiales. Cumple con lo esperado por el precio. Recomendable 100%

La description est celle du 6006. Sur la photo c'est le 6004 que je possède déjà et que le vendeur m'a envoyé et que j'ai retourné.....

I just received the item and all the parts are there and the owner manual provides enough information as to how to use the jaws safely.

Tour à bois