Kylo Ren Mask Darth Vader Helmet Belt SW Deluxe Cosplay Costume Replica for Halloween

When I received the Chest plate and belt, it looked as if nothing worked. Instead of sending it back I was determined to at least see what I could do. I opened the back of the chest plate, 2 screws, and found the black round battery case. I pried the case loose and found a spot on the side to pry it open, surprise, no batteries. I looked at the belt and loosened the belt over the 2 lighted boxes. I found the same round battery cases, pried them open and no batteries. The battery cases were held in place by thick double-stick tape. (Important) The battery cases must be lined-up with a window on the bottom of the belt and chest plate to access the on-off button. Since there are no instructions I used the try and fail method to find the correct batteries. (Important) I found each black battery case requires two (2) CR2032 button cell batteries for a total of 6. My local Dollar store had them for one dollar each so I bought 6. Installed them, made sure lights worked, snapped the black top on the battery case and used the thick double-stick tape to line it up correctly. I was absolutely thrilled to find that there was an "on" mode as well as a "flashing" mode for each of the light units. Not exact, but at least closer to the movie costume. The belt is tight but I can fix that as it can be fixed in the back and won't show. I have the cheaper costume but I love it because it's lightweight and not bulky or hot! The cape flows beautifully! I also have the full head mask, gloves and breather sound device. My hot topic boots have 3"-4" soles and heels, with helmet I'm 6'5". The chest plate on the cheap costume is a painted rubber material sewn on the chest. I found that if I take the back off the lighted chest plate and trim off 2 silver rubber pieces (with a scissors) that the new lighted chest plate fits directly over the existing one! I used Scotch M3 series 10-1000 super tape, thick double stick tape lining the back of the open-back chest plate. I discarded the metal back and screws. The super tape holds well, but in the future I will have to change batteries so I did not opt to use glue. I can now say (in a very low voice) That I am quit pleased. The lack of batteries was, disturbing. But the circle is complete, I feel I can now rule the galaxy.

Rated a 2 because of the depiction of the original Darth Vader helmet, or would have rated a 1. Would definitely not buy again nor recommend. The mask was packed in a baggie the size of a quart, which caused distorted the entire mask, due to the packaging. I do not consider this a helmet as it was not hard-shelled but is made of latex. Because of the packaging it has been 2-days, and the indentations have still not straightened out. The mask smells so bad, that it is impossible to wear without airing out as we experienced headache. Unfortunate as the actual mask itself is a good depiction of the original Darth Vader helmet, but the quality for the price is just not worth it.

Belt: With no directions to remove battery covers, found out you have to remove the whole battery case with double sided tape so you can see notch on side to split open (like on a key fob). Make sure the push button lines back up with the opening without getting the double sided tape dirty, or it won’t stay in place. Paint on plastic was a sloppy job.Chest piece: Same thing with battery case. The front plastic was painted over the red/green led’s, so I had to scrape off paint so the lights shine through.Battery cases: Be careful when pushing the button to turn on or off, or you might push the whole battery case backwards or sideways and won’t be able to get to the button again unless you re-adjust the case.Seller: Shipping was fast, and they didn’t make the product, so no complaints against them. (5 stars for seller).It’s a toy made of molded plastic and painted over, so don’t expect it to look realistic.

Used it to wear in a video, and posted it on Instagram. Love this beautiful and durable mask. May the force be with you ✨️ 🙏 😊

The chest plate and belt are made very well however replace the velcro before using it will not hold and will fall and break! I was told before I received my second due to the belt not wanting to light up! However when the replacement arrived and I redone the velcro everything worked and its a great addition to my vader costume

See photo. My son is absolutely thrilled—for my child’s joy, it gets 5 stars. I am making this costume for his upcoming fifth birthday. He is tall for his age, but on the skinny side. These are the items I needed to make this work:1. I had to alter the belt to fit a child. It was no big deal with a leather needle, black thread, and some elastic. If you need this for an unusually small (or large) person, I would go ahead and buy those items. If you don’t have a sewing machine, your neighborhood shoe repair shop could probably handle any needed belt alterations very easily.2. It comes with Velcro on the chest piece, but the other side of the Velcro is not included. I just ordered Velcro.3. You need six total round batteries. I suggest ordering those at the same time.4. You need screwdrivers.

build quality is solid and rugged, size is accurate and button layout is true to the box layout however the COLORS of 2 buttons were incorrect, i DIY painted over them to correct the color scheme but other than that its a solid purchase. the belt is also very durable with a combination of stretch bands and clips linked to leather straps.

It should state LATEX in the title..and maybe they shouldnt fold creases into finished items..For a MASK its ok... in no way shape or form is this a helmet..But the weathered paint scheme is nice it fits ok and the mesh is even around the asymmetrical eye slit...And the price should be at mask price...there are numerous nicer masks at 1/2 the price