Pneumatic Jack 16 Inch Lifting Height 3 Bag Air Jack 6600LBS Capacity Jack-Long Adjustable Folding Handle(White, Long Handle 3 Ton)

Finally received it after the 1st one was lost and it works great (1-time so far). Based on other reviews I found that the handle bolt holes lined up without a issues. I added a 3/8" Braided Expandable Sleeving Cable Loom that you would use on electrical wire to help prevent the chafing and possible bursting of the nylon inflation tube (hope it works). Used it to raise my 1985 Buick Regal to replace front wheel bearings without any issues at 90 psi with 60 gallon compressor. Once it was up to height I used a jack stand to support it. Nice and steady up and down if you monitor the pressure valve used to inflate and deflate.

Stopped working after 6 months but i repaired it easily with $2Lets start with the bad:1. Puck at the top is held by 1 thin bolt in the center so it breaks easily if jack is slightly misplaced.2. The cheap air hose runs inside the handle, which can move from 90 to 180 degrees so these movements overtime caused the hose to collapse internally near the hinge. This restricted air flow and caused the jack not to lift or release air.Repair: unbolt the base and replace the hose (I bought 1 meter of polyurethane OD8mm x ID5mm air hose for $2). Works like new again.This thing inflates and deflates so quickly that it saves me a ton of time compared to using my super heavy and loud "rapid" pump floor jack, so i dont mind spending 5 minutes to replace this hose once or twice a year. Alternatively, could also leave the handle down all the time or limit the fully up position to avoid kinking the hose.

It's lighter, cheaper, easier to use, and much faster than Hydraulic jacks that can lift only about a third of what this jack does!Since it's lighter and because of its design it can use urethane wheels that are larger and roll easier than other jacks.My only two complaints are that the handle is way too short to slide it under the rear end of a car, and the tar feed hose is some oddball metric size that I haven't been able to source ANYWHERE, even industrial hose outlets. Changing the air line fittings so far hasn't proved to be easily possible either.They REALLY need to offer a longer handle or a kit to lengthen the existing one!I can easily make a new longer handle, but since the existing handle is also an oddball metric size, you can't lengthen it with commonly available American tubing or hose. I bought a second jack to use that handle as an extension. I will make a new handle for the other one, and figure out how to change the air line fittings later.Also, several friends bought these jacks, and they have different sized metric hoses than mine!

This check works perfect and is very quick and efficient and getting my car up in the air. Also, it is small compact and easy to store. It does not take up a lot of space in my garage. I also love how quickly and efficiently this can get my car in the air so that I can put my jackstands in place.

My dad is a car guy that has everything so when I saw this unique pneumatic floor jack (something he admittedly had never even seen before, SCORE!) I had to get it for him.First with the positives. I was amazed to see that this is rated for 3 ton. That's pretty impressive (dad thought so too). Probably the nicest thing about this is that it is WAY lighter than your standard 3 ton floor jack. Instead of lugging around 70-100 lbs, this little guy weighs in at under 40 lbs and is much less awkward to maneuver. The second coolest benefit is the lift rate. This little guy inflates super fast getting your car off the ground in seconds. The other benefits should be pretty obvious, no pumping and so forth.A couple downsides: While it is very light, the lever adjustment from high to low in order to wheel it around is a little tough. It might just need some breaking in for the pins to be able to slide into the slots more easily, time will tell. My dad also said that there must be some sort of telescoping rod in the middle of the air bag to keep it straight as it inflates. Unfortunately, if this isn't perfectly straight, the telescoping sections must bind a bit because it'll get stuck and then shoot up quickly and it does the same thing when lowering. Again, some of the downsides are going to be obvious. You need air to use it so you can't just throw it in your car quick to use it at a friends house (unless they have an air compressor too). My dad has several buildings but he has an air compressor in each building so this is not an issue for him but you also couldn't take it to fix a flat on the side of the road either, for example.All in all, it's a pretty neat and unique tool for the shop. It did make a good gift for my old man. If you're going to mostly use this for tire/break work in a level area like your garage it would be great. A couple fine tuning adjustments on the engineering of this would make it a must have.

So, yes it has cylinders inside that expand as it gets taller to assist with alignment, and yes they bind up when raising/lowering as the vehicle tilts during the lift, but I personally am not afraid it will tip or drop the car. Things do get a bit dicey when it’s in its highest position, especially since the binding causes it to jerk up or down a massive chunk jostling the car around, but the contact patch of the tool to the ground is so big, I doubt it’ll do enough to tip it unless you’re really off kilter! Just apply more air or release more air and it’ll keep going as expected, jerking and jostling alike. The contact plate at the lifting point is really wide and rubber too so it’s difficult to slip off as long as the wheels on the ground are chocked or locked in some way. I have a one car garage and a 4gal air compressor, this tool has been absolutely outstanding in my arsenal! Quickly move the Jack from one corner to another in a tight space and the car is off the ground and in position in under a minute! I have the one without the long handle. I put Jack hydraulic fluid on the interior cylinders but maybe I’ll just lube it with the brake grease and call it a day, it’s merely a metal to metal contact that keeps binding up.

This jack works great. If you're using it on the floor you'll probably want the style with the long handle but this one for me I couldn't ask for more

Llego incompleto el producto

سهولة تركيبها وتم تجربتها ترفع سريعا ويمكن التحكم في الارتفاع بسهولة العيب الوحيد بها هو خرطوم الهواء لا اثق به رغم انه يبدو متين ولكن لا اظنه يتحمل عوامل الطقس من حرارة وبرودة وشمس

mon premier le manche etait soudé et les soudure non pas tenuecelui ci les bolts tienne bien la poignier

after a couple uses, the jack broke something inside of it and now its not stable at all and i wont use it anymore, i was wondering if there is a warranty on the jack? i did love using it as i do all my family's and friends tires and really easy to use and fast