VEVOR Maple Top Stainless Steel Work Table, 36x30 Inches, Modern Kitchen Prep Table with Lower Shelf and Adjustable Feet

Good value, sets up exactly as pictured. The butcher block is unfinished wood. Sanded, yes, but porous. Legs get about a half inch of play to level the table.

My husband needed a very sturdy table(most workbenches start at 48 but he needed a 36” hard to find yet this was perfect in this size with a wooden top to be able to bolt & put a machine on it that has a high vibration & this is a very sturdy table so he’s pleased and the generator went on the 2nd shelf below. Strong table for being smaller it’s great! He put the table together without looking at the directions because he said it was easy, it didn’t take him long and my daughter helped him to carry it to his workshop. He loves this table and says it’s very well made! The wood looked of good quality too! Nice having the adjustable legs as well. All around great table & recommend!

This is a generally well made table, with a two layer oak top (definitely NOT MAPLE), stainless metalwork (except for the leg sockets that bolt to the underside of the table top, which seem to be carbon steel, or perhaps a much lower grade of stainless than the legs and bottom shelf) and overall very nice fit & finish for the asking price.The top came pre-finished with some sort of open oil treatment, but there were three "fills" where knots or chips in the wood were covered with wood filler. If you intend to use this as a direct cutting or dough working surface, then that could be an issue, but if you're just using it as a utility table, then they should be no problem. I chose to re-sand the top at 220 grit and apply an oil that also contains beeswax, but for many users that would be unnecessary, since the finish it comes with is pretty OK and much better than I had expected!The legs and bottom shelf are stainless steel (hardware too by the look), but quite thin/light compared to a real commercial prep table, they will undoubtedly do fine in most home kitchens, but I would take the rated weight capacity as a maximum value, not as a working load. The bottom shelf should also be loaded with lighter items near the center and heavier near the legs, if you want to put a lot of stuff on it ...it's just relatively thin sheet steel and has no reinforcing frame (most commercial tables have either much heavier gauge sheet metal, or a frame, or both).The adjustable feet work well and have large bottoms that should be fairly kind to floors, but the core of the foot is plastic and small shreds of plastic that were deformed when the upper part of each adjustable foot was crimped into the bottom of their corresponding leg are visible at those seams.It didn't come with any instructions, but there's only one possible way that it goes together, if you aren't at all mechanical, then get a friend who is to help with assembly. As a bonus though, it did come with one extra piece of each screw, nut and washer, as well as a 5mm hex key, which is the only strictly necessary tool to assemble the table its self, though a wrench or pliers helps with getting the lower leg bolts as tight as they ought to be. Attaching the utility hooks, requires a drill and correct size bit, but the hooks are the weakest link in the whole design and I'd suggest leaving them off anyway.All of these criticisms aren't to say that the table isn't good (it definitely is!), but to point out the differences between this and a $600-$1000 commercial table that has the same basic appearance.Not everyone needs commercial grade durability and this table definitely fills a budget/utility niche very nicely.

No directions, things didnt match up the way they should. The top is great, however everything else is not great. Metal legs and bottom shelf came scratched up and damaged. Not even close to worth for the price

My husband talked me into getting this because of the discount and how much I started baking. It was easy to put together, it is sturdy and we use it as an extra space when we cook and bake!We did have to buy oil for it just because the wood was a little rough but it wasn't something that wasnt an easy fix.Highly recommend!

Only 32 1/2 inches high. Supposed to be 35 inches. Missing nuts and lock washers for shelf assembly. I had to run to the hardware store for nuts to finish assembly. And there were no instructions included. Granted, not rocket science, but come on. Overall, it is a great table, but not sure I would buy from this manufacturer again.

I have tried various silicon mats and bread boards for bread making. I found this maple-top work table and use it for nothing but making homemade breads. The 36” x 30” size fits perfectly in the center of my kitchen. It is heavy and it does not move around, even when kneading dough. The bottom rack easily stores 25 lb bags of flour and anything else you might need to keep handy in your kitchen. Even sticky sourdough cleans up easily on this table top with a bench knife/scraper. I recommend!

We have an area in our kitchen that is both a sitting area/breakfast nook and a work prep station for large family events. This table fits perfectly and took about eight minutes to put together - well worth the price. If you buy it; you'll need to get some food grade mineral oil also to bring some moisture back to it.