PC Products70147-2 PC-Clear Epoxy Adhesive Liquid, 1oz Double Syringe, 2-Pack, Clear 70147

The product works well. No surprises..The stopper or lid/cap that holds the liquid mixtures in is well designed and comes on and off easily. You don’t have to cut the tips and deal with annoying snap-on caps/lids. The lid/cap simply twists on and off. I’ve used the product four times already removing and putting back the lid/cap. No mess and the cap/lid works and comes on and off without issues..The plunger is smooth and trouble free..The two liquids come out clear and transparent, but turn slightly opaque when mixed. The epoxy mixes into a liquid consistency similar to chocolate syrup rather than tomato catsup, so viscosity is not that thick, so it will run. I recommend using a tray to mix. I used a piece of cardboard and experienced some running..When applying, note that the epoxy is lesser in terms of viscosity. It will run off your scraper and spill, so take care. But spillage is easy to clean with a wet paper towel..Don’t over-apply. Just make sure you can get even costing on both aurfaces/sides of the materials to be bonded..No nasty odors..A couple of minutes after application, the epoxy feels sticky and rubbery, but that goes away and the material will turn rock hard after an hour or so. Epoxy dries clear. Hardly noticeable even after applied on a wooden door that is painted white..Very good bonding. I used masking tape to clamp/hold the glued pieces together. And the tape came off easily after curing/hardening..I would most definitely buy this product again.

Used this epoxy as a finish top layer to cover a long (the >3 feet long) granite bench >1/4 inch-wide crack filled with strong adhesive glue and colored to match the granite. The gap of the long crack could not be clamped to be narrower without completely breaking the 2 -3 inch-wide long edge of the bench into many pieces. Plus there was a partially deteriorated supporting metal plank upon which the granite bench was glued, so the two pieces were hopelessly separated. Estimate prices to repair or replace the granite bench was ridiculously too expensive. So I used ChatGPT4.0 to come up with solution: First I cleaned out the gap with brush and vacuum. Then filled the length of crack with strong adhesive glue (LOCTITE PL Premium 10 oz. Polyurethane Construction Adhesive) from above and later from underneath where rust had deteriorated some of the metal support. I filled it just slightly below the surface level. I trimmed with a razor blade if it cured higher than surface level. Then I colored the visible tan colored glue with markers and acrylic paint to match granite colors and pattern. Finally, I applied this epoxy layer to protect the colors and pattern from water and make the repair flush with the surface of the rest of the bench. The epoxy was somewhat self-leveling, but can shave excess edges with razor as needed. Not bad for a DIY in an area not readily seen by visitors. Hope the epoxy can withstand the humidity and water exposure as the product claims it should.

Use to put finished heads on flies I tie, needed clear for covering eyes and showing thread color without any color change, doesn't set up as quick as I would like but stops moving after roughly 20-25 minutes.

Works well, but dispenser does not store well. Probably not an issue unless you use only tiny amounts at a time.

Adhesion is the best.

The epoxy works nicely. Its double syringe is well designed, and it makes it easy to put the cover back on for future use. Highly recommend!

When this product is mixed thoroughly, it performs well, but if you want to pour it, or work it into cracks, the mixing process is too time consuming for the amount of remaining work time. I needed to mix most of the 16 ounces, so I could pour the product into fairly large voids, so I short-circuited the recommended mixing instructions, in order to have more time for my pour and application. That turned out to be a problem. In some areas of my project, where A & B were not adequately present/mixed, the end result was that it did not harden, and remained somewhat sticky. I used this on a piece of apple wood I began turning on a lathe. There were parts of the wood compromised by rot and powder beetle tunnels, as well as bark space overlapped by other wood growth. For the most part, the pour went well, but the material that was not mixed properly, did not harden, and the result was that it did not "tool" smoothly, and it did not attach well to adjacent surfaces. So, I tried again on cracks that were revealed with more turning. I tried mixing a smaller amount. I tried to be more intent in the mixing process (which took longer). I was only a few minutes into the spreading of the product into holes and cracks, when a chunk appeared. Realizing it was beginning to harden, I worked feverishly to use product that was still liquid, but alas, I was only able to use about 80% of my mix before it got very hot, and hardened to the point it was not usable. I will admit, this is my first time attempting this kind of work with epoxy resin, so I don't know if there is a product out there that would be easier for me to get a "total mix" and still have enough open working time to get it applied. I wanted to include pictures, but am not savvy enough to know how to bring them over. Sorry.Ben

It does what it’s says on the tin

Fantastic glue for all those broken objects around the house. Used it on ceramics, glass, metal, wood and anything else that needs it. Easy to dispense the right amount, mix it up and you're ready to go. Make sure you give it some time to cure - it's not superglue but a super glue :-)

Muy buena aunque es muy poco precisa. Huele muy mal pero supongo que es por la resina.

Excelente epóxico, de verdad que sí pega el cristal, ya lo utilice en el cristal de mi comedor y de verdad que sí resiste..

good sturdy extruder

Very good epoxy but heads up - this is an insert that is to be used with an dispensing gun. It's not very clear from the description so I didn't realize. Managed to make it work for me though.