Cooler MasterCryoFuze Premium Performance Thermal Paste, Nanoparticles, | 2 Grams | Thermal Compound (for GPU, CPU, Consoles, Laptops Graphics Cards, Heat Sinks)

I would sum it up like this: The paste is excellent in performance, but would be very difficult for someone applying the first time to successfully apply.This isn't your MX4 or MX5 -- Cryofuze Ultra is very thick and dry. If you used IC Diamond back in the day think a bit more dry than that. Spreading is nearly impossible without heating the tube a bit with a hair dryer. This gives it just enough pliability to be workable.The plus side is that due to the paste being so dry, it shouldn't have any issues with oil separation. Once it's on the temperatures are great, easily rivaling what I've seen from Kryonaut. The line method seems to be the easiest if you have a high clamping force heatsink. Otherwise spreading it is next to impossible without heating the tube up.Time will tell how long it holds up and keeps good temps. I have it running on a 4790 in a HP Z1 G2 as a test. Those tend to be a little toasty, but it's done a great job bringing the temps down from the MX4 I had on there. I'm seeing 3 - 4*c temp reductions and a much quieter fan profile. The cores now idle only slightly above room temp (19.5*c room, 24*c idle)

Much better temps than MX-4 and MX-6. This paste is very thick and a bit difficult to apply but worth the extra effort. Noticeable drop in temps on both cpu and gpu.

This grease was a bit tough to apply evenly, I wiped off twice due to frustration but the third try (and the last of the tube) worked out. My method was a pea in the middle, then spread out in one direction, then the other. and repeat this method. I error to have less on the sides of the chip and more of a thick middle as it squeezes out to the sides and pushes the air bubbles out with it. I managed completely even temps across all cores and along with a cooler master 280mm AIO my I7 12700kf doesn't break 48c after 4hrs of pubg set to ultra.Ultimately performance is top notch, and this 2 gram tube is cheap enough you can give it a couple goes if need to, but I could probably use it again on the first try knowing what I know now.Biggest tip from me is to clean the new CPU with alcohol before attempting application, I believe this is what allowed it to stick better and get a good adhesion. I did not clean the new cpu face and had problems with adhesion/spreading until I did that. I will be using this in all of my new builds for sure. Way cheaper than thermal grizzly, longer lasting and better preforming (on paper as I have not run them side by side due to the cost difference)

Keep in mind, I have not applied thermal paste to a CPU in 10+ years, but this one was a little thicker and drier than what I used before. It made it slightly more difficult to apply, as when you go to spread it, it would pull off part of what was already applied and you'd have to go back over it. The spreader it came with was not very helpful, went back to using the inside of a lense wipe packaging and got it spread evenly.That said, once it was applied, the CPU has run cooler than what it was running before. I did pair this with a water cooled heatsink though, so hard to say if it's both or just one of those two. I would buy again as spreading it wasn't super difficult, just not runny as what I remember thermal paste being.

Good thermal paste. It keeps my temps down and I haven't had any of overheating issues with my 13600kf. It's been in my PC for about a year and a half and still works fine.

It was slightly strange applying this thermal paste as it seemed quite a bit thicker and more viscous than paste I've used in the past. I ended up using an x pattern because I wasn't sure about how this paste would spread. Despite this, my thermal performance has been quite good. At the end of the day the thermal paste you use doesn't make a big difference in performance but this has been running my Ryzen 5 5600 with a Hyper 212 black a little bit cooler than it did before I had changed the paste. At idle I get roughly 38 degrees C. Great price, slightly cheaper than most other well-known alternatives so that was a plus.

Excelente producto bajo unos 15 grados en juegos exigentes. Muy efectiva.

Es una pasta termica super efectiva relacion calidad-precio