* Self-Healing Clear Paint Protection Film Kits (Bundle-DoorEdge_DoorCup_Doorsill_RearBumper)

I recently installed the Install Proz Self-Healing Door Edge Protection Film on my vehicle, and I’m genuinely impressed with its performance and ease of application.Installation Process:The installation was straightforward, especially when following the provided instructions.Make sure to thoroughly clean the door edges before applying the film. Proper surface preparation is crucial for optimal results.Self-Healing Properties:The self-healing feature is remarkable. Minor scratches and scuffs disappear over time.It’s reassuring to know that my car’s door edges are protected from daily wear and tear.Invisibility:The film is nearly invisible once applied. You have to look closely to notice it.It doesn’t detract from the car’s appearance or draw attention.Durability:I’ve had the film on my car for several months now, and it has held up well.It withstands car washes, rain, and sun exposure without any signs of yellowing or peeling.Peace of Mind:Knowing that my door edges are shielded from accidental bumps and scrapes gives me peace of mind.It’s a cost-effective way to prevent unsightly chips and dings.The Install Proz Self-Healing Door Edge Protection Film is a practical investment for maintaining your car’s pristine appearance. Whether you’re a meticulous car owner or simply want to protect your vehicle, this film delivers.

The instruction card that comes with it states you can install using a wet or dry method and then proceeds to give instructions for a wet install. Don't do a wet install, install dry. Their videos even say that dry install is now the preferred method. Also, do not peel the entire backer for the adhesive off at one time. As you install it you can pull a little of the backer off at a time so you can press it against the door a little at a time as you install. After you have the front side attached to the door gradually work it around to the back. I had this for a while before I installed it so they may have updated their instruction card in the meantime. Wish they sold slightly longer rolls, 150" wasn't enough to do both my truck and wife's SUV so had to order another roll.

If you've read any of these reviews, you've already heard this . . . but it is definitely worth repeating. It's all about the surface preparation. Get those door edges (inside and out) as squeaky clean as possible and take your time applying this protective material. Do that and I think you'll be happy with the results. By investing in some time cleaning the surfaces as well as I could, it made the installation of this clear, adhesive film super easy. Durability? Not so sure at this point but it's been two weeks now and it appears to be on there very solidly and there's no signs of wear, looseness, or discoloration (yellowing). Hardly noticeable at all. You have to know it's there and look for it to really see it. Cool!UPDATE: It's been nearly two months since I applied this protective film on my vehicle and they remain securely on there through many car washings, rainstorms, and constant exposure to the sun. No signs, to this point, of any yellowing or cracking.

Pretty slick. Take your time and make sure the surface is CLEAN CLEAN CLEAN. Make sure to buy a small spray bottle (I went to a beauty supply store) and fill it with 25 percent iso alcohol and the rest water. Follow the directions included and it shouldn't be that hard. I found that the solution evaporates quickly so keep spraying it as you go. Also, the tape lays down nicer and is easier to work with if it is not stretched. Stretching should only be needed for curved areas. If the area is really curved it might not stick to the back side of the door though. Your finger should be able to get most bubbles out, but I used a small squeegee to put the finishing touches. Get the bubbles out as you go, or else it will be harder to get them out later when the glue starts to dry. I was able to do a good amount of all 4 doors of my GMC truck.

Note that I have not used or installed this product. My review is of the application process only. The film requires several steps of preparation to be successfully installed. Cleaning the edge of the car door with rubbing alcohol is easy enough. But you are also supposed to spray the film itself and the door with a solution that is neither identified nor included in the package I received with the product. Then you have to apply the film when the edge is still wet, and to heat the product itself and the edge of the door with a hairdryer for more secure application. I learned these things through a video that was not available on the website referenced in the installation guide, but is available on youtube.com. Would not have purchased, had I know of these steps. Will return and buy the 3M protective film instead.

This stuff is actually quite amazing! I just bought a brand new 2018 Camaro and when my friend opened the door to look inside he bumped the edge of my door against the truck next to my car. No damage done that time, but not got me thinking. I don’t want to ding up the doors on my new car. I didn’t want something that would stand out and make the car look bad. This is the answer! Almost invisible and extremely tough.

I wish I would've gotten this sooner. It applied easily and looks like factory finish, enough to play with as well if you mess up.

The adhesion of this product is not good. Also bubbles easily. Not even worth returning.