Neewer Metal Bracket Compatible with Canon G7X Mark II & Mark III, Camera Extension Base Plate with 1/4" Tripod Mount, Microphone Stand LED Light Vlogging Accessories

It arrived in a small cardboard box, there’s a folded piece of paper giving support contact details, as instructions are not necessary for such a simple device.It screwed to my Canon G7X Mk.2 without a problem, using the small Allen key supplied, but there’s also a wide slot allowing a screwdriver or even a small, thin coin to be used. As advertised, the compartment door for battery and memory card is easily accessible. I also proved that it does not obstruct the tilting LCD screen’s range of movement and no other buttons, or connector panels are obstructed. In fact, it would appear that you can even use an AC adaptor, since the little notch in the case side can still be used, as long as you slide out the cover before attaching the bracket, see my photos.Since the retained fixing screw is flush with the bottom of bracket when mounted, the camera still sits nicely on a flat surface. There is a tripod bush on the underside, allowing the bracket to be attached to a tripod. On my G7X Mark 2, the camera’s own tripod bush is well off the lens axis, the one in the bracket is about 15mm camera left, almost, if not exactly, (it’s difficult to measure) on the lens axis. Further points of good design.I attached a small LED lamp to the cold shoe and the clamp tightened OK. Unfortunately, my intended use was to attach an external microphone via the cold shoe - until I discovered that’s only possible with the G7X Mk.3, which this bracket is apparently also compatible with.In summary then, I can barely* fault the design or finish for such a compact solution. Obviously it unavoidably makes the camera a little less snug fitting to the right-hand, but the hole in the base allowed my thumb and forefinger to grip the left-hand-side just as I would normally. When there is something attached to the cold shoe, you may end up holding that instead, if it is bulky. E.g. a small microphone could be encompassed by your hand, but (say) an LED light, or optically slaved flash (strobe) unit, could not.* If there is one minor aspect I’d suggest be improved, it would be to have a very slightly thicker bit of metal on the cold shoe top edge, this measures 0.96mm thick on mine, I’d suggest 1.1mm thick (in total), would be better. I don't think that would foul any cold shoe devices.

This is a must-have for photographers. It is so helpful to have a hand grip that is compatible with my camera, especially since I am always shooting on the go. This is a great product that is affordable and reliable. This is a must-have for photographers who are on the go and need a reliable hand grip.The metal bracket is pretty easy to install, and it makes my camera feel more sturdy and secure. I really like the design of this hand grip and the fact that it is compatible with my camera. The grip is easy to use and makes it easier to capture beautiful photos. Overall, I recommend this hand grip to anyone looking for a simple way to take professional quality photos.This is a must-have for photographers who need extra support for their hands when shooting. The hand grip is easy to use and lightweight, which makes it easy to put on and take off. I like that it's easy to mount on my camera and it is compatible with the Canon G7X Mark II and Mark III. This is a great tool for photographers who need extra support for their hands.

"Long Story Short"Solid metal framePerfectly fits cameraPlenty of uses but having it as tripod or stick mounted with microphone mount is perfectSolid finish, no doubt that it is durable and will last longPerfection from NeewerValue for money 10 out of 1`0

I bought this to give myself options of adding additional lighting or audio recorders to my G7X. Unfortunately there is only one shoe on this rig - and no hotshoe on the camera. So bit limited on my options. However it's solidly made and fits well to the camera, without increasing its size by much. This is now my go-to solution for family videos and snapshots so not a bad outcome.

Neewer Metal Bracket Hand Grip Compatible with Canon G7X.Like all products from Neewer this camera handle grip is built to last. Fitting only takes a few seconds, and away you go!. I leave it on permanently, there's no need to take if off to change batteries etc. The construction is lightweight alloy, meaning very lille added weight to the camera.

Looks great but after tightening it doesn’t fit the g7x mark 3 so will have to send back

As is always the case with Neewer, this is a very good quality product and outstanding value for money. It's easy to fit and to remove and doesn't cause any scuffs or scratches. It's just as good as an OEM part and Neewer as a brand has never let me down.

I was always struggling to get footage on my phone for tiktok & on my camera for YouTube! This small item fixed that problem quickly for me! Now I can record on both at the same time without having to hold both at the same time if you get what I’m saying! Absolutely amazing product! I actually found this one off of tiktok. Another creator posted a video!

Queda perfecto y seguro, de buena calidad!!

Very sturdy. Aluminum and the Canon one was super flimsy plastic.

Je n'ai plus besoin de démontrer mon micro externe pour changer la batterie

Achtung! Nicht kompatibel mit G7X Mark III!Man kann die Schraube nicht komplett festziehen und die Form passt nicht 100%ig.