CHUMXINYBrake Bleed Kit for Shimano,TEKTRO, MAGURA Range of Hydraulic Disc Brakes, Including High Performance Mineral Brake Fluid (120ml).

All you need to bleed and restore your hydraulic disc brakes on your bike/s. Worked fine on my mid price Shimano sets. Would imagine that the additional parts and adaptors would work with most other popular brands (but best to check). If you’re new to doing this, consider checking out a YouTube clip first and rehearsing the process beforehand. Straightforward really, but easy to goof up (embarrassed to admit I mistook a fixing bolt for a bleed valve in my rush..) Enough in this kit for several bleeds. Stopping power restored!

Cheap and comes with all the pieces you need. Firstly, it comes with all bet bits you need to bleed the braked on Shimano Ultegra R8000 Road Brakes. You do not need to buy the Shimano adaptor.I will share an idiots guide below in case anyone needs it.1) Slide the brass retainer over the clear tube and push the end over the syringe. The brass ring is to hold it tight.2) Remove the wheel, retaining pin and screw to remove the brake pads.3) Fit the yellow brake pad in the void and re-apply the retaining screw (If the yellow block won’t fit, use something to push the pistons back then apply again).4) Slide the tube clamp over the tube5) Attach the hose and syringe to the bleed valve, using the 7mm spanner (included), open the bleed valve, literally 1/2 a turn.6) Close the tube clamp and go to the lever.7) Peel the hood back, expose the screw.8) Using a 2mm Allen key, remove the screw and keep safe.9) Find the yellow adaptor to fit the hole, try the larger ones first.10) Attach the yellow funnel and 1/2 fill with oil.11) Release the tube clamp and draw the fluid back into the syringe until there are no bubbles (you will see the fluid being drawn out of the funnel)12) Close the bleed valve on the calliper then pump the brake lever a few times, you may see some bubbles, but until it feels firm. (Took me about 6 pumps then it was solid)13) Push the plunger into the funnel to stop oil leaking out when you remove the assembly.14) Carefully unscrew the yellow Cullen and adaptor, when removed re-apply the brake lever screw and tighten.15) Clean the area of oil, isopropyl alcohol works well, or just wipe with a tissue and put the hood back.16) Clamp the hose at the syringe, carefully remove and immediately wipe the area clean.15) Re-assemble the brake pads and wheel etc, and enjoy your new brakes.I cannot fault this system. I am a 1st time brake bleeder. It took 5 minutes, worked flawlessly. You don’t need any other kit, or to pay your shop £25 to do it for you.

Great value, got my brakes bled without too much fuss, the only thing i'd like to see changed is that its pretty hard to get the bleed block between the caliper pistons, so i manually ground a little chamfer on the lower edge to make insertion of the block a bit easier - then it was easy from there on. with this one little change from the manufacturer, the product would get 5 stars from me.

Great value for money and easy to use

I used it for the first time to bleed the brakes on my bike. There are many adapter types that cover most if not all the bleed nipples. Using the syringe to add pressure to the fluid, I pumped the brake lever and removed the air from the system.

Worked well and plenty of adaptors instruction booklet easy to followWould recommend this to my friends

Overall the kit was fine, the barbed connector for my tektro hydraulic brakes didnt have long enough thread with the o-ring in place, managed to get the job done with a little fiddling though

Revised review; Seller excellent attention to detail - customer care/quick response. All parts included, neatly packed for after use storage. Recommended.

My Tektro brakes were mushy after fixing a flat. After checking a few videos, I realized I probably had gotten some air in the system while taking the rear wheel off and changing the tube.This system was perfect. Multiple adapters that fit the mineral oil opening without leaking. I topped off the fluid and sealed the system without spilling a drop of oil.Now, the brakes are solid and work as expected.Worth the money.

This it was perfect, never don't a break bleed before and iv got 3200 km on this girl and she's going strong, it was extremely easy, only thing was that it didn't have the break dam for my scooter but that ok I skipped squeeze the handle and got the bubbles out and everything works just fine, just remember DO NOT SQUEEZE your breaks without a break dam, its a pain fighting those Lil calipers apart to the proper width, especially if you do it without your break pads in it lmao.. you'll learn, I did lol

Ich bin zufrieden, hat alles gepasst. Auf dem Video ist zwar ein anderer Bremssattel beschrieben, aber man findet alles.Ist auch Alles dabei , grosse Auswahl an Adaptern. Nur halt , man braucht nur einen.

Remolie is het hydrauliek remsysteem vernieuwd en tevens ontlucht. Alles zat er bij en het werkte perfect

I only used the mineral oiltonfill and bleed the air out from the break handle. It worked very well an now my brakes works again. I like that it includes the oil.Used it on my Kaboo mantis 10 pro scooter who has zoom brakes on it.