Talon DIY Material Grip Sheet - 5"x7" Adhesive Grip - Rubber or Granulate - Made in The USA

Many happy users of this grip covering relate how easy it was to install, and how long lasting. I'm applying it to a drop forged steel knife to cover the grip - easy to apply, grips well, adheres with little fuss, long lasting. it's doing the job without the disadvantages of paracord or the mess of multiple wraps of utility tape, and, ti also looks good, to boot. I added a smaller piece to the scabbard to knock down noise and break up the outline, it's a better mix with camo clothing when hunting.Certainly a better choice with much better grip than paint or duct tape.

Since I have many different firearms that don’t have custom grips made for them. The customization ability of this product allows me to custom fit all my firearms. Excellent product, that I have bought several.

It's good for if you want to put grip tape on but have no room for it

I used this to make my phone case grippier. I used to use egrip stickers for this, but I ended up trying Talon instead.The good:- It sticks really well, even where I cut it into narrow strips. Much better sticking than the egrips. I am hoping it will last a long time.The bad:- The surface is rough, but it is not grippy--it doesn't have that nice silicony stick-to-the-hand feeling of egrips. That's probably a good thing for the *intended* use, namely guns.

I rarely write a review but had to in this case! I just got the Talon Grip Material in this morning via UPS. It comes in a 5" X 7" sheet which is plenty big. I was originally looking for a Hogue type grip for my CZ Scorpion as I have them on all my ARs. I love the tactile grip and sticky feeling VS a hard plastic grip. I couldn't find one for the Scorpion. So I bought the Pakse Pathfinder grip from HB Industries as it had the correct angle... Thought for this review it wouldn't matter what grip you had.First, I created a pattern using painters tape. Looking at how custom grip material was applied to other weapons I have, I knew I was going to overlap the material on the finish... So I cut it a little longer than I needed. I removed the tape and traced my pattern in reverse on the back of the Talon material. It's white paper so it is easy to trace. I used a pair of sharp scissors for most but also used an exacto knife for some of the round inside corners. Since the grip is 3D and the paper is 2D... An exact tracing probably won't be possible. You need to remember that this stuff bends and stretches a little as needed when applied... And you will be able to trim to fit while you are applying it if you are careful and have a sharp exacto knife handy.I cleaned the grip per instructions with isopropyl alcohol. I wiped it down well and got out the hair dryer to make sure everything evaporated. I lined up the grip material and slowly applied, peeling back the paper as I went. I needed to trim a few spots where I was off on the pattern. It was VERY easy to work. I slowly worked it around, pulling and trimming as needed for a perfect fit. Once wrapped completely around and overlapped where I started... I broke out the hair dryer and heated it all up. I did this several times, allowing it to cool in between. I pressed down EVERYWHERE! It molded exactly to the grip as I wanted.The grip now feels almost as good as a Hogue. I was also left with a piece large enough to add some tactile strips to the front of my HB Industries Pakse Sapper MLOK front grip. Two small strips on either side on the bottom. WOW! This is SO much better than stock! Picking up the gun and shouldering it now feels much more comfortable and tactile.Hope this helps someone make a choice!

Talon grips and grip material is well worth the money. Easy to install and adheres very good.

This is a really great product.If you heat up the product with a hair dryer before using it it gives you a maximum amount of flexibility very sticky, really good stuff?I would not lie this is awesome

Great product. I’m all in on talon grips been using the for years but the arrival after shipping was pushed back two day. Didn’t live up to the advertised arrival time unfortunately.Again great product but expect to wait.

Turned out great for my Logitech G604 Mouse, Fairly easy to cut.has a good grippy texture to it. this was my first time buying some grips for a mouse and i'm pretty happy with it so far. The Adhesive is quite sticky and and tough to pull off but if you do remove the grips to re-align it, it does not leave any residue, but only time will tell so well these will hold up.It's got a good feel to them so if anyone was thinking of trying this out, i'd high reccommend it.still have alot left over too.

Lässt sich super zuschneiden und trägt in einer angenehmen Art auf. Verändert das Griffstück nur minimal besser als 3M Safety Walk

ColdsteelのCode４のグリップのすべり止めとして購入しましたモノとしては完全に分厚い紙やすりで、焼き入れされたS35VNに傷をつけるほどですポケットに入れるにはアグレッシブすぎるので貼るのはやめました

Good quality grip. Love it. Thanks.