VEVOR Universal Tracor Seat, Lawn Mower Seat with Micro Switch and Drainage Holes, 6.3-11.8 inch Extended Slot Tractor Seat for Tractor Loader Excavator

This seat is built well and is a good price. It's very cushioned well and comfortable to sit in. It compares very well to the original seat in my Bolens GT-1800 lawn tractor. I was looking forward to using it, but ultimately it couldn't be used.It comes with a set of position adjusting sliding mounts. The holes in the seat for the mounts don't quite line up with the holes in the mounts themselves; they need to be kind of wedged in to be used with the 4 captive nuts in the seat bottom. When mounting them and tightening them down, I found that the seat bottom metal deformed, which was surprising to me. Still usable, but not as strong as I thought it should be and might be a weak spot with continued use.The right hand side sliding mount has a set of catches (notches) and a release handle; the other side slides freely. I really liked the idea of being able to adjust the position of seat. However, while I never actually rode my tractor with the seat installed, I was worried that the left hand slider may slide around a bit going over bumps and hills. I would have liked to have seen a cable to another release lever and notch on the left hand side slider to ensure the seat won't slide on one side.There is a built in occupancy sensor made to kill the engine if you stand up / fall off the seat.Unfortunately, on the Bolens GT series and Troy-Bilt GTX series tractors, shorting (closing) this circuit kills the engine, but this seat's sensor is shorted when sitting. The sensor is wired the opposite of what these tractors expect. This means the tractor runs when not seated (and brake off) but when seated, the engine dies. To be compatible with more tractors it would be great if this seat included a toggle switch or another set of leads to be able to wire the seat so that "open" is "seated" and "closed" is "unseated".I also tried mounting the seat directly to the seat pan on the tractor (skipping the rails). In this setup, the seat was 4-5 inches too far forward. An offset bracket would have to be used to be able to position the seat farther back.In summary, I believe this seat would work well for the Bolens / Troy-Bilt tractors if:- both sliding rails were notched and were locked via an adjustable cable- occupancy sensor allowed reversing its output so that "seated" was "open"

Worked great on our Case garden tractor and the sliders are a bonus!

The product is just as described. Universal. Bolted up to my craftsman ys4500 riding lawnmower. Would have been nice if they sent the bolts to mount the assembly to the actual mower seat bracket, but I had some self tapping screws laying around that I used and it worked great! I have a new seat for a lot cheaper than OEM factory replacement.

The seats are very nice for their price time will tell if they will break or crack in the weather

Had to modify slightly to fit Kioti tractor, works good.

A little confusing to mount but works great, seems to hold up well too.

After using the seat 2 time the edging that holds the material on started coming off.Waste of money and time.

To start off, the seat it self is very nice. It’s comfortable, big enough, and seems decently well made. BUT. the instructions are absolutely awful. They don’t tell you how to do anything. Figure it out your self, where the washers go and which way the sliders face. Also, once you get it mounted and on, it does not slide easy AT ALL. It’s super hard to move when your off the seat, and impossible to move when your sitting on it. Which makes the seat basically useless. Just buy a non adjustable seat

B+

Comfortable, simple seat. Great quality, plenty of leeway with fixing / bolthole positioning. Fitted directly into my application without fuss. I'd definitely buy again.

Sitz ist wie beschrieben und für den Preis alles in bester Ordnung

Comfortable and sturdy. Didn't really need the slide mechanism as the tractor already had this but I was able to install the seat with the slide onto the existing slide. This has the added benefit of giving it an inch or so of additional height and more range back and forth, both of which are welcome.

Garden tractor seat right out the Box not damaged just open plastic bag found foam from seat sticking out took me 3 hrs to hot glue it back together pull back together so could use it