TAC Side Steps Fit 2015-2025 Chevy Colorado/GMC Canyon Crew Cab (90deg Bent Ends) Pickup Truck 3" Stainless Steel Side Bars Nerf Bars Running Boards Rock Panel Off Road Accessories 2 Pieces

These fit perfectly, add a nice touch on my truck, are highly reliable and greatly appreciated by my backseat passengers who are usually shorter folks.

I wanted to get a set of these a) for looks and b) so that my nieces could get into and out of the truck easier.They worked out perfectly. They look just as good as the factory option for about 1/8th the cost. Installation took me a little over an hour. Basically, you'll want to sit down and study the instructions some for a bit (they're perfectly usable but slightly confusing), but once you figure it out everything bolts on quickly and easily to the pre-existing holes.If I had to make a MINOR complaint it would be that while the truck has 4 factory mount points available, this set of steps only utilizes three of them. For all i know the factory steps might also do the same and these seem perfectly sturdy, but one more bracket wouldn't have hurt.Overall though they were a great deal, are sturdy, and look great.

Very pleased with the product. Install was easy except for the front bracket. I needed my son to pull the plastic as far back as he could without damaging it so I could get the two small bolts in to hold the front bracket. Once the front brackets were installed, the rest was easy.

And they look nice!First I read the directions then unboxed the parts. Parts are clearly marked PF for Passenger front, PR for Passenger rear, DF for Driver front, and DR for Driver Rear. I separated the hardware by passenger and driver. I also separated the bolts, washers, and lock washers by size: listed as 6mm, 8mm, and 1/2 inch in the instructions.Tools needed:1. T-15 bit2. Pocket knife3. 13/32” socket4. 10 mm socket5. 13 mm socket6. 3/4” socket7. RatchetMy 2017 Canyon doesn’t have front mud flaps but does have front fender covers. Besides the 2 screws holding them in place, there are two plastic clips which are hard not to break.1. Remove the front fender covers with a T-15 bit.2. Next I removed the 2 factory screws under the front fender covers with a 13/32” socket.3. I then removed plug sets 1, 2, and 4 using a pocket knife to expose the mounting locations and installed the 8mm clip nuts. Skip the 3rd mounting location.When installing the support and mounting brackets, do not completely tighten. (Tightening all bolts will be saved until the sidebars are in place.)5. Install the passenger right front passenger support bracket using the 6mm hex bolts and washers with the 10 mm socket. Then install the passenger right front mounting bracket with the 8mm hex nuts, flat washers, and lock washers using the 13 mm socket.6. Next move to the center and install the passenger center mounting bracket with the 8mm hex nuts, flat washers, and lock washers using the 13 mm socket.7. Move to the passenger rear and install the passenger right rear mounting bracket with the 8mm hardware using the 13 mm socket.8. Carefully position the passenger sidebar up to the front and rear mounting brackets after removing the black plastic end caps. Attach the sidebar on each end with the 1/2” hex bolts, flat washers, and lock washers using the 3/4” socket.9. Center the sidebar threaded inserts with the center bracket and attach with the 8 mm hardware and 13 mm socket.10. Level and adjust the sidebar as needed then tighten all hardware with the appropriate sockets.11. Repeat the above steps on the drivers side.

I added these side steps to my 2021 Chevrolet Colorado. Great instructions and pictures! Just lay out the pieces as shown, look through the instructions and get under the side of the truck to match the picture to the parts. Everything, including the 'speed nut clips' and braces are heavy duty. The first side will take 1 1/2 hours (learning curve) then the second side will take 1/2 hour. (You will need to remove the front short mud-flap if you have one- -easy). They look great and fir perfectly!

Running boards look great on Truck and so helpful getting in and out!

Look great! Installed in about 1.5 hours after watching a YouTube video and reading the instructions. I didnt use the smaller front backers because the fender bots are welded on. Seem very sturdy without. Great buy. I did purchase an open box deal, when I opened the box it was a mess but all parts where there.

Rusted the first week. Very disappointed!!!

Unfortunately these developed rust spots on them after the first winter.