VoswitchUniversal 8 Switch Programmable Switch Panel

Just amazing

I have a 2016 Sierra with several additions including an auxiliary battery, winch, front and rear LED lights, and an air horn. Hey, I’m from Alabama what did you expect? I quickly ran out of space for switches on the dash, and did not want to cut any holes in it either. There was also a large number of extra wiring harnesses, inline fuses, and relays. I decided to install a switch panel that integrates everything in one panel. I needed one that can change colors to match my red dash lights, dim, and also have the ability to make the switches momentary, you know, for my air horn! There were a ton of different kits out there, but this was the only one that offered all of the features I was looking for. It also included a pre-populated waterproof enclosure that came with relays and fuses.The kit came very well packaged and with all necessary installation items. I was able to mount the panel to the same spot I previously had my switches installed. When you install the unit, just take your time and pay attention to the directions. I used wire loom and created a new harness for the wiring from my accessories to try and keeps installation as clean as possible. When done, I had eliminated a big wad of wires from under the hood and have only a single control cable going into the cab which is not visible. When you look at the pics of under the hood, the red wire that is rolled up is the remote turn on wire that hooks to a circuit that is on when the ignition is on. I currently have it installed using the power switch on the panel to turn it on and off. I ran out of time to run that last wire and will address that in the future. The relay box has a set of dip switches that enable either manual on/off or on with accessory power. Either way, the unit can be turned off with the power switch on the control panel and will remain off until turned on via the switch. I hope this review helps.

The availability to turn on the unit ONLY after turning the key to ACC is definitely flawed (not the low voltage cut off I think). It will drain your battery whether or not you flip the switch on or off. The unit will continue getting power regardless and voltage drop reading will be the same. The voltage drop will actually decrease to 0.2V (0.006V drain) if you disconnect the thin red trigger wire or the button box inside the vehicle. WHY CANT IT DROP TO 0.2V (0.006V drain) when the trigger wire to ACC is installed? Who knows. I believe I may have a faulty unit. I understand there must be a tiny amount old voltage drain for the unit to retain the memory settings, but c’mon. The unit should not be powered at all with a trigger wire installed. If I wanted it to be powered I wouldn’t have connected the trigger wire (will draw current regardless of wether it is connected or not).I was incredibly exited for this, but after quad checking my entire vehicle, I realized that this unit is draining my vehicle. I’m honestly incredibly disappointed in the product.Reasoning: Power Probe and Multimeter diagnostic. Voltage drop test results on a 0.6V, which translates to 18mV or 0.018V. Enough to slowly drain your battery in about a week or two weeks.Solution? You’ll need to constantly charge your battery, and who wants to do that? No one. It can probably be solved by installing a bigger battery for your vehicle to gain cold cranking amps. I already have the best possible battery for my vehicle. The only solution for me is to switch from a 51R to a 24F or constantly charge my battery. Ridiculous.

Update,6 months of use so far and everything works great. However the control panel is starting to delaminate a bit.I installed this on a 2018 Toyota 4Runner to run a light bar, ditch lights and rear flood lights. It was super easy to install, looks clean and makes adding off-road lighting and accessories much easier. Only one wire needs to go through the firewall into the cab and you can control up to 8 accessories. I mounted it to my relay/fuse box under the hood and attached the trigger wire/add a fuse under the dash. Works wonderfully, and the timing from pressing you on button to the lights activating is great. Multiple background color choices and tons of stickers for whatever accessories you're adding. It came with everything I needed to install and multiple ways to mount the switch. The only thing I'd like to see added to the package is a Blue Sea Bus bar to ground all of the negative wires too. But I have one on the way, and I'll definitely be recommending this product to other Overlander's and off road lighting users.Thanks Voswitch for making a complete and well priced product to meet and exceed my needs.

This product works just as advertised and does it well. Adding accessories has never been easier and the box where all the connections are made has been completely water tight since I’ve owned it.Note: I did learn a lesson about the switch panel itself, the hard way. It is waterproof but it is not power washer proof. I never sprayed directly at it up close but it did get water in it which caused it to stop lighting up and working altogether. I contacted the seller and they were quick to reply and although it was my fault they warned me about the pressure washer and are sending me a new panel. I’ll just remove it from the machine from now on when I wash it. Do not hesitate to buy this! Well worth the money and the customer service is awesome 👍🏼👍🏼