Residential Misting System- Made in USA Pump- 200 psi Mid Pressure Patio Misting System-12 Nozzles Misting System

I did some fairly extensive research regarding misting systems prior to making this purchase. I knew that I would not be satisfied with my system if I did not purchase a pump to go with it. However, I was trying to stay within $200 for the entire system - with the exception of the nozzles and pump, everything is pretty much cheap plastic in most systems if you think about it. Anyway, I found this kit on AMAZON, made the move, and am very glad I did.Install was a breeze and I recommend using 1 1/2 inch SPAX construction screws for the brackets that hold the hose line in position. I used longer SPAX screws for the pump and drilled hole with silicone before pushing the wall anchor in. I'll admit - the pump was the biggest concern I had prior to making this purchase. I am happy to report that the pump is very quiet, has functioned flawlessly, and has stayed flush mounted to the wall without issue. I was also concerned about the system leaking at the connections - again, I was surprised to see how high quality the product was. If you follow instructions and make sure your connections are secure, you will not have any issues. Make sure you do your install measurements and mock up your nozzle placement before you buy so you don't have any surprises once the system arrives.The ONLY issue I had was with 2 nozzles being clogged within the first two weeks. I followed the guidance in the instructions and ran water through the installed pipe prior to fitting the nozzles (to clear debris from the lines). I let water run through the system (w/o nozzles installed) for approximately 5 mins. I felt that the system was clear and installed the nozzles. Of the 12 nozzles, I had issues with 2 "misting" properly (they were clogged). To resolve this, I took the nozzles off and sprayed CLR into the nozzle orifice. I left it soak for about 10 seconds and then submerged it into sink water and shook it around. Then I used gentle compressed air to blow the nozzle orifice from output side back toward input side. This technique has resolved the issue and the nozzles flow perfectly.In my opinion, this is a very cost-effective option and any DIYer could perform this install.

The pump ran for a few hours and overheated. Not good. Why in the world would you sell a mist system pump that doesn't cool itself with the water? Either way, if it shuts off it's wordless to me. I'm not willing to do any additional DIY to make the pump function as it should out of the box. I'll give the company a few days to get back to me before I return it to see if they have a solution.You can piece together a more robust system with copper tubing for about the same $ on Amazon with a likely better pump.

The product came as advertised, only issue that I see is that in Dallas the humidity can be high, the .012 nozzle's were a little too large, it got everything wet when used. This could be my design, I'm forced to angle the nozzle's in toward the seating area instead of away. I did, however, purchase the .006 nozzles and it's yielding better results than the .012, time will tell. I am happy with the performance and the quality of the product, it's easy to install and works as advertised. Quality of the pump looks and performs well, it's quiet and I have it attached to the side of the house, no noise transmits into the house due to heavy rubber insulating grommets. Connecting hose is strong and looks to withstand harsh winters and hot summers. Easy to hook up and get working, word of advice, ensure that you flush the system before attaching the nozzles, I didn't and I ended up plugging a few of them. Helps to read the instructions, that was my own fault not product design. Product would have received 5 stars if offered with .006 nozzles and not the standard .012

Ignore the bad reviews!!! I’m convinced you won’t find a better cost to performance misting kit than this.I have it installed in a 12x16 gazebo, 6 misters on each of the long sides. The picture is hard to tell but this thing MISTS!The pump. It’s a 200 psi water pump, it’s gonna make noise. But when you’re visiting with family, lost in a book, etc. you barely notice it. And it works so well it’s worth it. If you want no noise then just use a $30 cheeser mister.Installation was a breeze. I had to use heavy duty zip ties and they did the job excellently. The fittings are easy to seat properly and don’t leak at all if done correctly.I just wish I had more places to install these!

Just installed and fired up the system. I installed 9 nozzles over a distance of about 18’. Install went well. I highly recommend flushing the line prior to installing the nozzles. One of the T’s got clogged at some point, and it’s easier to fix then than later.Overall the installation took about 3 hours including measuring and cutting the supply line.I am thoroughly impressed! I was concerned about the noisiness of the pump due to its placement close to my chairs. But it’s whisper quiet. So relieved.It mists as you would expect, but at less than 2’ on center, the nozzles put out more water than I really need/want. I think things may eventually get wet. I’m going to take another reviewer’s advice and purchase the 0.006 nozzles to reduce the total output and hopefully increase the fineness of the mist.I’ve read some reviews about leaking. One other piece of advice is to push the lines completely into the T’s. They go in farther than you may think, and they meet some resistance about halfway in, so be firm with them to make sure they seat properly.Overall, my expectations have been exceeded, especially considering the cost. Definitely recommend.