American Modified JL Look Style Tail Lights w/Brake & Reserve Lamps Smoked Lens for Jeep Wrangler JK/JKU 2007-2018, Pair

Fast shipping, lights are really bright and love the style. Put them on my 2012 Jeep Wrangler JK. There were no instructions, however there is an instructional video on the product page. One watch then simple and easy install.They've been on for 2 weeks so far and been through 3 rain showers with no moisture yet. Hopefully it'll stay that way.

Easy install and lights e bright n they look dang good on my jeep 🥰 very happy!!!

The first one was a complete pain in the rear to install, had to pull it off a few times because the clip kept popping off the tub. I figured it out and have included instructions below. Second one went on in about 5 minutes. Super bright and they have a DOT stamp molded into the plastic so there is zero question about their legality.Instructions:1. Remove inboard two screws of stock light housing, the outboard two screws are only to hold the lens on.2. pull light housing off of tub corner, detach the connector from the stock light and attach it to the new one and set it on the bumper. Now is also a good time to feed the small connector with two wires through the hole in the light for the reverse light.3. Open accessory bag and remove contents, use the small screw and nylock nut to attach the load resistor to the L bracket. This is important as the bracket undoubtedly serves as a heat sink for the blinkers to prevent the fast blink. Attach the two s clips to the short end of the bracket and slide it onto a bit of the sheet metal seams inside the tub. You will be able to see what I am talking about when you look inside, the driver side also has the fuel filler neck so be careful around that.4. Inspect the bracket screwed into the light housing. If the angle is not approximately 115 degrees open it up. If it is acute at all the lip will slide off of the inside of the tub when you tighten it.5. Unscrew the allen screws until the bracket is about 3/4 of the way down the screws A T-30 torx will also work for this.6. Slide the bracket into the opening in the tub and pull the light housing towards you and screw in each screw a bit at a time so it pulls into place evenly. DO NOT OVER TIGHTEN!Finally connect the reverse light, push into place and repeat on the other side.This is how I installed them and it worked for me. I noticed a few complaints that there were no instructions and I was happy enough with the price on these that I did not mind writing this of my own free will. I was not asked just a Jeeper who wants to help other Jeepers. If these instructions do not work for you or you overlook safety while installing and get shocked that is on you I take no responsibility. Be smart and be safe and have a good time on the trail.

Okay, I had to leave a review for these after poor Tori D. said: "My husbands is a sheet metal construction workers and puts stuff together all the time and could not figure these out." He's either lying to Tori or he needs to find another line of work. These lights are very straightforward on the installation, I can't imagine how anyone with any common auto skills couldn't figure these out! They look good, only time will tell if they hold up. To Tori D., sorry these didn't work out for you because they are a simple and nice upgrade.

Love the look of the lights and they were easy to install. They are bright and would be great but one of he reverse lights doesn't work. I would have given this product five stars but receiving a partially functioning product is a bit fustrating. As you can see from the picture the brighter light on the passanger side is the reverse light that works and the one on the drivers side doesn't.

These taillights were very easy to install. They are very bright. Especially when backing up in the dark. They look really good on my Jeep also.

These are great looking and unique! Extremely bright, took me months to finally decide on which ones to get, and I don’t regret getting these. Love them so far. The reverse lights are extremely bright too. Only time will tell if they last.

My 2015 JK’s tail lights were looking dated and these are 100% worth getting! The hardest part is screwing the little nuts onto the bracket with the gold piece. Best way is to hold the nut with a needle nose pliers and slowly use a drill with a Phillips head to tighten. Lights are very bright and high quality.