FogiMount Hex Desk Monitor Arm Fully Adjustable, fits 6 Screens up to 27" (Enhanced clamp Mount)

This product leaves much to be desired in sturdiness. The receivers that connect the horizontal arms have a recessed part to accept a tightening screw but there is no hole on the arm to insert a screw. As a result the horizontal arms are loose an if bumped could probably just fall off. Definitely a design flaw.I would have returned it except we had already cut the desktop mount to customize it to install where we want it instead of the edge of the desk. Instead we'll use some hose clamps to tighten the horizontal arms which does not look professional.

so i bought this to replace a 50inch TV i was using as a monitor. having never used more then 2 monitor stands before, i wasn't sure what to expect in the end. having said that, this stand does definitely have some design flaws.first off, to tighten the Center Piloting Anchor Point: it is a beveled donut with basically a clamp. to adjust the tension, you need to hang the monitor, wiggle it around and see how much you need to adjust it. then you have to turn a Screw Driven "fine tuning adjustment column" to be able to access the allen key screw in the back of the bowl to adjust the tension, then retest to see if you need to adjust the resistance on being able to move it.Second: to anchor this to a table there are 2 large Eye-Bolts, if you have a desk with a back plane under it, you will need to make sure you have enough clearance, most desks do, but not by much. and to get these Eye-bolts tight enough to support 6 monitors, you better have a solid wood desk top and a 4 foot cheater bar, otherwise every time you bump your desk, you're monitors will jiggle a significant amount.Thirdly: the arms cannot fold backyards, only forwards, so if you have a Center Monitor on the stand and wish to not use the right arms for some reason, you cannot simply fold the arm in on itself behind the desk, it can only go forward into the back of the center monitor, which will not work unless you have a really weird monitor that has a very large but steep attachment point.having said all of this. this product works fine for me, even though i had to change up how the rig is put together. but the design in general is not great. i also forsee that should i finally take this off my desk, there will be "chew marks" where the stand had to be excessively tightened to the desk to increase stability. if you are still thinking about buying one still, make sure you have a solid wood desk, or carpentry skills to make reinforcement plates. and make sure you have at least 6 inches of "under desk" to attach the clamp to? if the backing is too shallow and not about "hand depth" you're wasting your time ordering this.

６画面対応の21.5インチのモニターアームの種類は非常に少なくて、こちらを購入してみました。半日掛けて設置しました。。。剛性だけはしっかりしているものの、高低差が全くつけられず、全く同じ６画面のディスプレイですらセンターとサイドの高低差が激しくついてしまい、その調整の自由度が全く利かずでイライラしてしまい、「これは失敗作だから捨てる」という決断をしてようやく気が晴れました。２１以下であればサンコーのクネクネか、エルゴトロン製の２画面対応×3買ったほうが良いです。まあ、この商品は物干し竿には使えるのではないでしょうか。最悪です。というか取り扱いやめてるし・・・（販売店）

この手の製品にはあまり縁がないので、感想だけ・・・・21.5Wインチディスプレイでも使用可能だが、ほぼ平面になるので、モニターに囲まれるような感覚はなくなる・強度はかなりある方だと思うが、アームの遊び(緩くはない)があるので、重量のあるモニターだと、両脇が下がる　≫もしかしたら設置方法しだいでは改善する可能性あり・モニターの重量に合わせた机が必要とあるが、止め具部分が小さいので、かなり頑丈な天板と重量のある机じゃないと無理　≫職員室にあるようなスチール製の机も多分無理、天板がベコりそう・左右のバランスをとって設置しないといけないため、設置が面倒1つのアームで固定できるのはお得感があるが(実際安いし)設置環境を整える支出も考えるのであれば2台縦設置型の物を3個用意した方が安上がりになる可能性もあると思うしあと、モニタの付け替えもらくだと思うモニタサイズの制限もないですし