Fireblack® Hi Temp BBQ Smoker Gasket Self Stick 15 ft High Heat 1/2 x 1/8 Black

I recently installed the FireBlack Hi-Temp Gasket on my smoker, and I couldn't be more impressed. The installation process was incredibly easy, making it a hassle-free upgrade. The gasket looks great and provides a perfect seal. A quick tip for those looking to install this gasket: make sure your surfaces are very clean. I found that using alcohol makes quick work of cleaning the surface, ensuring the best adhesion. Overall, the FireBlack Hi-Temp Gasket is a fantastic addition to any smoker, offering both aesthetic appeal and exceptional functionality.

I recently paired the Fireblack® Hi Temp BBQ smoker Gasket Self Stick with my Louisiana Grill vertical smoker, and the results were nothing short of spectacular.1. Seal Integrity: This gasket offers an impeccable seal, locking in all the flavorful smoke where it belongs: inside the smoker. Say goodbye to leaks and hello to more robust, smoke-infused flavor in every bite.2. Easy Installation: The self-stick design made installation a breeze. No fuss, no mess - just peel, stick, and you're ready to smoke.3. Heat Resilience: Capable of withstanding the high temperatures of serious BBQing, this gasket is built to last. I've used it repeatedly with no signs of wear or degradation.4. Economical Efficiency: By preventing smoke escape, it conserves both fuel and wood chips, making every smoking session more efficient and economical.5. Enhanced Performance: Since fitting this gasket, I've noticed a definite improvement in the consistency of my smoking sessions. The flavors are deeper, richer, and more uniformly distributed.The Fireblack® Hi Temp BBQ smoker Gasket isn't just an accessory; it's an essential component for anyone serious about their BBQ. The improvement in flavor and efficiency makes it a no-brainer for Louisiana Grill vertical smoker owners. Happy smoking!

Was able to use this roll to do two smokers. Both smaller units but worked out perfect for me.Make sure your surfaces are very clean and free of any risidual smoke. Alcohol made quick work of everything.Installation was a breeze. The easiest way to trim was with a sharp pair of scissors.Not a fault of the gasket but you aren’t able to put it along the top and by the hinges. It keep your door open because of the thickness of the gasket. Works well everywhere else around the lid but wasn’t able to make it seal the top.

I got this gasket to put around the firebox door for my Dynaglo smoker. It went on smoothly. The self-stick backing was a little tricky to peel in a couple of spots, but otherwise it gave me no issues. Stuck perfectly and has held up through a couple of smoke sessions and some inclement weather with no problem.I thought it would be a little bit thicker but the size is clearly disclosed so that's on me - just remember that 1/8" isn't as thick as you might think. It is doing its job by making a tighter door seal and preventing excess smoke escape. It's made of a coarse felt-like material, not a solid foam or silicone, so expect that.I have no complaints.

Very easy install, looks great and seals perfectly- not sure of the durability yet, but enough came to do my PRO 575 twice. Cheap and easy enough to do once a year.

I had none of the problems other reviewers noted. It cut well. The backing peeled fine, and it has remained stuck to the smoker surface soundly. I did prepare the surface like I would for anything I was preparing to stick something to with an adhesive: I cleaned the area around the door opening with a general cleaning spray on a cloth repeatedly changing spots on the cloth until no color (from soot and ash) was visible. My Treager Pro 575 smoker has an excellent power coat paint (or hammer finish enamel. I don't know which) that is shiny. Then I used denatured alcohol (or rubbing: isopropol alcohol will work too) to remove any detergent residue until the cloth showed no discoloration again. Then peeled and stuck the strip of material WITHOUT STRETCHING it, cutting to length after getting close to the corners with an exacto knife with a new blade through the backing and then through the rest of the material. That works better than scissors for sticky-pad type materials. Then peel and stick the remainder to each corner for a perfect fit. The smoker keeps heat in much better than before especially when windy - and is surprisingly quieter than before while running. It also is a quiet-close smoker now. No clanking when closing the lid. Just a dull thud.

I purchased this to seal the gaps and leaks in a Cuisinart vertical charcoal smoker. I think it does its job perfectly and was definitely worth it.Pros:-Fairly easy to install - I had no issues cutting it to lengths I needed and it seemed to go around the curves without any issue. The adhesive seems pretty strong as well-Stopped all my leaks - no more smoke leaking out where it shouldn't beCons:-Not much here other than needing to be careful when applying it. The adhesive is pretty strong so be precise about where you want it to go.-Sometimes it would stick to my finger - this is more user error than anything else, but occasionally when removing the backing my finger would come in contact with the adhesive as well as some of the fibers which were a little difficult to remove from my fingers.

The felt material is acceptable. My complaint is the adhesive. It's not strong enough and I mounted it on to a new Kamado Kettle Grill, let it cure for 24 hours, did my initial burn in, and didy first cook. After the cook. I saw a part of the felt gasket came up and not adhering to thr grill rim. You may spend more money replacing this gasket than anything else.