VEVOR Hydraulic Shop Press, 12 Ton/26000lbs, H-Frame, 4-Hold Adjustable Height, with Movable Plates, for Garage or Professional Users, Orange

Got this to straighten out the forks on my mower. The forks are about $180+ shipping and tax each, this press was just under $170 delivered, taxes included. Used it to straighten both forks and it paid for itself the first time I used it. I have had a few other projects where it came in very handy since then. It doesn't take up a lot of space and it does pretty much everything I need it to. Anything I need done that this can't handle, I'm better taking to a machine shop anyway. It's fairly light, but also strong. The instructions could certainly use some improvement, but it wasn't too hard to assemble with just a little common sense. I plan on relocating it from my carport to my office/workshop and adding some casters to make it even more useful

Only issue I had was that no matter how much I tightened the bolts for the base, it would go out of square. I ended up shimming between the uprights and base and that easily took care of that. Otherwise, I easily popped my wheel bearings in and out.If needed, you could probably swap for a heavier duty jack, but I don't believe the frame will withstand much more than 6 tons.Also, I didn't look at the dimensions and was expecting something a bit bigger. I guess I was expecting a freestanding model, lol... it's more of a bench top press. Still works fine for my uses. If not better since it's more portable.

I don’t normally write reviews but I thought I would share my experience with the 12 ton press bought specifically to replace my rear wheel bearing in a 2001 4runner. The reason this one works and the harbor freight 12 tons doesn’t, is all based on the cross member that supports what ever you are pressing. The two cross members are connected via two long bolts therefore you can slip in the entire axle and bearing removal tool in between the cross members.Cons: quality is not the greatest. I had some issues assembling the press but was able to get it all to fit. The final product was extremely lopsided. I had to wedge a pice of metal under one of the legs to keep it from wobbling.

Got the press to help with my C3 restoration. The box was open from the end so parts fell out. I opted not to send it back and took Amazons, discount. I really wish I had sent it back. Besides the missing parts which I can get at Home depot or hardware store this thing is short and not built very well. The center piece that gets all the pressure kinda just sits in between the uprights with loose bolts if you want to be able to adjust it freely up and down when you need to. What ill wind up doing is putting spacers between the support to be able to tighten the bolts and give me free access to adjust it up and down. I think it will do what i need it too, but i should have sent it back and went to Harbor freight and purchased the 20ton for 50 more bucks.

The press arrived in two nested boxes (a box in a box) but all pieces were present. Assembly was simple. I used a rafter square to ensure the feet were perpendicular to the risers and assembly took about 10 minutes. There are two sizes of washers and nuts. Four for the legs and two for the press table. The two included plates are minimal, but functional. The entire press is coated in orange paint which is already flaking off, which is anreplaceable. The included bottle jack is unsecured but easily replacable. One of the tabs broke off the relief valve immediately upon first use. Not a deal breaker for me given the low price of the press but not great, for sure. My major concern lies in the bolts of the work table. They are very weak (head reads 7.8 which is very poor grade) and there are no sleeves to maintain spacing. This means you cannot tighten the bolts down as the table would squeeze against the risers and make the table unadjustable. After only two presses, the bolts are bending and will have to be replaced. This isn't much of a problem for me as I have access to more fasteners and sleeves but I don't know how many other home-gamers are so fortunate. They really should have used much stronger bolts and included sleeves (just tunes that slip over the bolts to maintain spacing) as 6+/- tons of shearing force is quite a lot for suboptimal bolts to endure for very long. If you're using this as a platform for herbal pressing, this might not be such an issue for you, though, as the functional pressures are much lower.

Heavy duty - does the job!

i don't require a press often but when i do this works great. i found the support beam required spacers so it allowed for adjustment. could also use somewhere to hold the handle. i made my own but would have been nice to have been there OEM

Definitely a nice quality press to allow easy installation of new wheel bearings or anything else that needs to be done.Very happy with the item.Thank you.A+++++++

Presse très utile pour changer mes roulement de boîtes de vitesse, la mise en place de joint spi.Petit bémol que je ne peux reprocher au vendeur car acheter en connaissance de cause c’est la hauteur max des pièces que je peux mettre. (Un peu juste suivant l’utilisation)Pour les 6T ba je sais pas aucun moyen de vérifier donc on va faire confianceBref je recommande

Prodotto mi piace molto.L'ho montato velocemente da limpressione di essere solidoProvato a vuoto su piastra di ferro, sono contento! Leggeri difetti di verniciatura, ma non mi preoccupa.Piastra dove appoggia il cricco purtroppo è saldata storta ma penso che non incida su funzione. Altrimenti ci metterò un cuneo...Sono soddisfatto

Boven in de omschrijving stond 12 TON, Bij levering blijkt dit 6 Ton te zijn. Blijkt in de specificaties te staan in kleine letters