Stanley National S819-401 Stanley 819401 Assortment Heavy Duty Pegboard Hook Kit, 15 Pieces

These are the ones you want for metal pegboard such as Wall Control. They are in fact heavy duty, and well designed for 1/4 inch holes.They are easily inserted and removed from metal pegboard, but they are beefy enough not to fall off.See my pictures to compare these against smaller, typical hardware.

I installed a 1/4" pegboard in my craft room. I have had one before and really liked it except the hooks kept slipping out of the board when I removed an item. If you carefully read the descriptions you'll find hooks that fit both 1/8" and 1/4" pegboards. That is true but using 1/8" hooks in a 1/4" board results in the above problem. So it's important to purchase the 1/4" hooks. There are locks you can put on 1/8" hooks, but my board is nailed to the wall (it's 30" by 70") so can not be removed. It's very important to read the description. These hooks fit securely, but can be rearranged if desired. They also are very sturdy.

I ordered these because I have 1/4" metal pegboard, and the smaller sizes, while functional like to slip out.These were the correct size, and fit well. That said, the construction and quality control was terrible. 3 of the 15 hooks had the bottom peg attached crooked enough that they wouldn't fit in the holes. A little tap from a hammer fixed one, broke one, and straighten another (but it still wouldn't fit).Looking at the weld which attached the bottom peg - it's adequate for what it needs to do (sit there with little to no stress) but is a total joke.I'm not bothering to return these, but consider them pretty shameful on the part of Stanley.

I'm a huge fan of having my shop organized, and these are what make it possible. Overall, they're very study hooks that should last forever once installed. I found in one older sheet of 1/4 in peg board, I had to hammer the bottom peg in on some of these since they're so tight. That's the kind of fit I like in hooks since it means they won't pull out.That being said, I found a few minor quality control issues. First of all, the bottom pegs seem to just be tack welded on. Under normal conditions, I can't imagine this would be an issue, however like I said, I had to hammer a few of these into the holes. Out of this pack, I had one rear peg break off. The only other issue I had was the spacing between the top and bottom pegs. I found some instances where they were more than an 1/8th of an inch too low, or too high.In the end, I have to admit, I ordered another pack of them. Despite the few throw away pegs, it's still a good deal for sturdy pegs. I'd recommend them.

These hooks are in fact the Heavy Duty type as described by the other users. They fit properly in the 1/4" pegboard, unlike the hooks designed to fit in both 1/4" & 1/8", which do not fit securely, or need plastic anchors to hold them in. I purchased my hooks used from "Life and Home", fulfilled by Amazon. The hooks came with the cardboard back from the package, and are in perfect condition. Why they were available used is beyond me, but It reduced them to about $2/pack.This set contains 15 total pieces, including 5 Large "U" hooks, 5 small "U" hooks, & 5 straight or "L" hooks.

These are by far better than the hooks with no second alignment pin at all, but Stanley's quality control is terrible: this second pin is often misaligned or incorrectly positioned, and sometimes they just don't fit. I've bough a lot of Stanley tools that were very high quality, but these are very poor. Also, the secondary alignment pin is too small, which means the hook is not securely affixed when installed. Other vendors use a slightly larger secondary pin which assures a snug fit with the pegboard when installed. I would not buy these again.

I have 1/4 inch fiberboard pegboard and purchased these. They are well made and sturdy but are slightly too large to fit my pegboard. I'm really disappointed since the description clearly says they're for 1/4 inch holes. Too much of a hassle to return a $10 item but I believe the description is misleading or maybe the holes are slightly off although the pegboard is from a big box store and should be accurate.

This is a nice assortment of useful peg hooks. Not too long, and enough variety in shapes that they work very well for hanging tools. With one pack, I was able to hang my digital calipers, die wrench, bullet puller, primer tube, and pliers for my reloading bench, with several hooks to spare. Exactly what i wanted, and they fit very securely/snugly in 1/4" hole pegboard.Highly recommended!

Finding Pegboard hooks in the UK seems so hard to do. At least, finding them that will fit securely into 1/4" pegboard.These hit the mark very well. Solid with a lug that fits in perfectly with pegboard, my garage now has all my tools on the wall within easy reach.Maybe I watch too much american TV and see their garages bedecked with this stuff, but pegboard seemed like a great solution to rummaging for a tool I knew I had, only to find it later after I'd bought a replacement.