Starrett Tungsten Carbide Tipped Hole Saw - SM22 Sheet Metal Cutter With Arbor & Pilot Drill Bit - For Drilling Stainless Steel Aluminum Alloy - 22 mm

Very good quality with an accurate cut. I have used these for cutting accurate and clean holes in oak worktops, sheet steels and stainless steels. There is a spring that is used for ejecting the cut cores of thin sheet but this spring can also be easily removed to allow a greater depth in wood to be cut.Great tool

This is a very good hole saw and cuts through like butter

The seller was able to actually check the product off the shelf for me, instead of checking a computer inventory, which seems is almost unheard of these days. Good price for product and delivery. Top seller.The product does a great job and cuts a hole very precisely, without wandering around at the start. I bought the last one to retro-fit roofrails to my Mini Clubman; since I was cutting holes in the car roof (!!!) I wanted something that could do the job reliably and with minimal potential for error. This type of tool is probably more suited for use on a proper stand drill with little or no side play; the teeth being WC are very hard and brittle and are not designed to take loading sideways. Having said that, I used it (carefully) with a hand-held cordless and had absolutely no problems. Top product. The only down point with this bit is they only sell them WITH arbour, but it actually does unscrew, so now I have three of these hole saws, each with an identical arbour, which obviously means it adds to the expense.

Used it to drill 3mm thick stainless pipe and it did so with ease used a hand drill not ideal but worked the drill suffered (brand new Milwaukee) the bit did chip a tooth that's my fault for going hell for leather with it dry and full speed

I used this on trunking lid ,even used cutting fluid to stop friction but the edges broke on first use ,total waste of money

Boight this to cut holes in compact laminate worktop - worked beautifully, very neat hole and with a bit of masking tape to protect the surface no chipping or loss of edges. Have also drilled through formica laminate, 3mm stainless checker plate and marine ply - cuts well on everything. I've bought a couple of sizes now. Not that cheap but worth the money and I suspect will stay sharp for a good number of cuts.

Bought for cutting a hole in 1mm thick stainless steel. Made light work of it. Very satified.

This hole saw worked extremely well in my bench drill to cut through 3mm stainless steel plate. The drill speed was set down to the specified range and liberal application of a cutting fluid used (Molyslip MWF)Obviously important to manage the feed rate to maintain cutting but not overheat the cutter12 holes cut with no problem. Highly recommended.

Sharp, durable, awesome.. my uncle was a machinist so I've been classically trained in these sorts of items and things and this bears that name and lineage.Thank you!

Corta bien el acero inoxidable

Carbide tooth broken off after one use. Five holes in light gauge steel. otherwise seems a good tool.

I've had to punch quite a number of holes in stainless steel lately. I've been using the 1 5/16" EZARCs to great success. I've ordered a lot of them and haven't had to return a single one. However the 1 5/16" hole is just a tad small for me which requires me to open the hole w/ a carbide burr. In order to try and skip this step and not go too big I tried out one of these cutters. I ordered one and from the first hole something seemed off. After you got into the cut a little, it started chattering like a mofo. On the 7th hole, it completely failed and stripped.I figured I got a bum. The holes were just the right size for me so I said surely if I order two more I'll get one that works right. Little known fact, these are two piece cutters. Tecnically you can replace the cutting part. Well the first box I opened, the cutter wasn't on the shaft. I installed it, tightened it up and went to work. I didn't make it through ONE hole before the threads that engage the cutter stripped. Oh did I mention this one vibrates and chatters too? Crap what horrible luck I thought as I installed the second one that came in this order to finish the first hole. But damn, I must be amazing because I'm 3 for 3 as even the 3rd one chatters like a mofo on cocaine. I can throw in any other cutter and my mag drill works smooth as butter.The problem is these cutters. They suck. Seriously. They could probably pull a golf ball through a hose they suck so much. If only EZARC made a the size I need, I haven't had ANY problems with there cutters.This cutter blowwwwwwwwwwwwssssssssss more than Traci Lords.

Fonctionne bien