4 PCS Metal Sensors

Easy to set up with the Autel Scanner. I’ve done this twice and they work. There are YouTube videos on how to break the bead to access the sensor and it’s easy! Good luck

Cloned my 1st set by programming the same codes onto this new Autel set.... works seamlessly on the car!

Installed these on our 2007 Camry Hybrid. Last set of Autel MX sensors lasted 5 years (version with screw photo attached). It took me awhile to program these newer ones on my TS601 despite “saving” the codes last time. Process is not intuitive on software despite firmware updates for those that don’t do this as a job. In fact they don’t even list 2007 Camry Hybrids anymore since one of the updates to the TS601. I use these for my Highlander Hybrid as well.

Bought these and the programmer from Autel and I am so glad to finally not have to rely on the pricing and programming from wheel/tire shops when i do my alignment or get new wheels. With this kit and the Autel TS501 programmer it only added up to about $70 more than getting factory or other TPMS sensors offered by most wheel shops and I now can rotate my tires without having to visit a shop to adjust the computer to the new sensor location. With my next car or next wheel purchase this will end up saving me money.

I put these on a 2005 E55 AMG. Pretty straightforward to install if you have the right tools to do it. The really nice thing about these is that they can be used for 433 MHz and 315 MHz cars. I programmed them to be 315 MHz and my car seems to be able to read them OK. I will see how long these last. I put Mobiletron ones on my other car and they worked initially but now they do not work. They take a long time to wake up. These Autel ones seem to wake up pretty quickly so we will see. Programming is not super intuitive with the TS401 but works OK.I think people reporting DOAs don't realize that these need the Autel programmer to program and activate. I tried just reading them before programming just as a test and they would not react at all. It would be good if Autel put clear warnings every where they could that these need to be programmed first. Hope they last. I will report back if they do not.

First off, these are expensive. As just TPMS sensors, too expensive, about twice the cost of basic sensors. That said, these fit a fairly specific niche and they're the only way I've found to do what they do.Specifically, with the matching Autel tool (yes, it does have to be an Autel tool and Autel sensors), you can read the ID's of your existing sensors, and "clone" them onto these sensors. If you're like me, and have summer and snow tires, and have them mounted on two sets of wheels, you can have cloned TPMS sensors, so you can swap your tires without having to reprogram your car every time.Alternately, if for whatever reason you need to replace a sensor but can't reprogram the car, these will allow you to clone that sensor instead.It's a nice feature, for a small market niche, but I'm glad they exist.They programmed easily using a TS408 tool in my case, pulled the sensor ID's from the set the car "knows", programmed that onto the new set, and my car is happy again with no TPMS warnings.

its probably a good product, but since I didn't know I had to have there scan tool to program them, that sucked, so I wasted my money

Ordered this and the USB programmer. Programmer worked well. Wanted to change the bad one first to prove to me that it worked. Problem was that it was difficult to determine which sensor was bad. Not the fault of the equipment, but just an observation. Because the sensor was dead, the programmer picked up the other sensors. Needed to change two out before I got to the one that was bad. On the next car, I figured out to take a reading, then reduce the air pressure and take another reading to see if it corresponded to the reduced air pressure. As I moved around the car, I reduced the pressure to different levels to ensure I knew which tire was which. Then I got a reading that I couldn't ID....it was the spare. This time, I got the bad sensor in one try. Now that I know it works, I'll change out the rest.The sensors I received were missing the torque pin. I emailed customer service and the next day, they sent some to me in the mail. When you are installing these, make sure you have a torque wrench that can meter to 4 N-m or 3 ft-lbs.