Wedge Guys Golf Grip Kits for Regripping Golf Clubs - Professional Quality - Options Include Hook Blade, 15 or 30 Grip Tape Strips, 5 or 8 oz Grip Solvent & Rubber Vise Clamp

I regripped an entire set of clubs, saving myself a good amount of money from paying someone to do the job. You will need a good quality vice (I have a heavy duty steel vice on my workbench) and a sharp carpet knife. The instructions are easy to follow and I was very pleased with the results.

very good

Good product

Stuck well ,no real instructions , i put tape on peeled off paper covered the shaft untill slippery all over then pushed grip over shaft , you have to work fairly quickly to get grip into right place as it sticks quick ,used black rubber thing over to of grip pushing down top to bottom a few times seems to have done the job winning

Very easy to use, did a whole set of clubs in 1.5 hours arrived early good value for money recommend

The kit works well have now regrouped 6 clubs, very easy to use.

Glad I didn’t pay extra for hook blade used trusted Stanley knife

Quick turnaround with swift dispatch. Terrific product, exceptionally easy to re-grip 14 clubs. Highly recommended.

Very easy to use and includes almost everything you need. After reading and watching online info about regripping golf clubs it seemed simple enough. Make sure you have a steady stand or table with a clamp that can hold the 3" club holder, a pan or something to catch excess fluid and a sharp utility knife (apparently graphite shafts require a hooked blade to not damage the shaft.) My clamp is close to a wall so I clamped my clubs about 10" from the club head and it worked just fine and stayed stable considering how far from the grip it was. The club shaft fits snug in the rubber holder and won't slip. With a utility knife (with a normal straight blade), cut straight down the old grip (don't worry, it doesn't hurt a steel shaft but cut away from yourself as it will hurt you), remove the old grip and use the knife to scrape the old grip tape off, most of it came off easily without much effort (my sandy grip had never been changed, had it fifteen + years... blech) some excess I removed with Gunk Out but I'm sure soap, water and a towel would do. The grip tape strips are 9" I believe and not the exact length of my grips so I used 1 full strip and about an inch and a half of another to get full coverage per club with about a half inch to over hang the butt end of the shaft which you fold and tuck into the interior of the shaft to make a "water proof" seal. Didn't need to do fairway metals, putter or driver so using extra strips was no big deal for me. I used a plastic container under the clamped club shaft where the grip will go to catch the excess solution. After thoroughly coating the interior of the grip using your thumb to cover the pin hole on the end, pour solution into the grip and then cover the hole with your other thumb and rotate and shake the fluid inside to coat the entire interior. Dump the remaining fluid from the grip over the tape and maybe some more from the bottle. Line up the grip, lightly holding the bottom and using a towel on the butt end so there's no spray from the pin hole, quickly, in one motion, slide it onto the club shaft, adjust the alignment while it's still wet and remove from clamp and tap the butt of the grip on the floor to ensure it's snug. Dump the remaining fluid from your catch back in a/the bottle and you're done or ready for the next grip. Didn't use the spray nozzle it comes with, thought that might be sloppy. I simply poured about two ounces into the grip with my thumb covering both ends, sloshed it around then poured it over the tape and kept reusing the leftover solution. Easy. Watching YouTube videos on diy grip changes will give you a better idea than I just did. Just commit to sliding the grip on and don't stop (read lots of comments from failed attempts), use lots of solution, it's reusable so use a catch and use a lot of fluid, you can twist the grip straight after it's on for a few seconds (probably longer) before the adhesive really sticks. From removing the grips and tape to re-taping, applying solution, putting the grip on and making sure it's straight probably took seven minutes max per club! Really easy to do. I let them set for about two hours then hit the range and played a round with no problems. I highly recommend this kit from Wedge Guys Enjoy.

Great product and a great price

Highly recommended. Search in YouTube for the operating guide and this package provided all the tools required! Awesome purchase. Smell is not bad too.

Excellent quality. Easy to use. I replaced with new grips easily with this kit.

Great product, easy to regroup a full set of clubs. Enough to last quite a while, highly recommend.