M MINGLE Pressure Washer Coupler, Metric M22 15mm Male Thread to M22 14mm Female Fitting, 4500 PSI

Worked great

When I went looking to upgrade my SunJoe SPX3000 pressure washer (2030psi, 1.76gpm advertised), I was at a loss at how many adapters I would need to replace the long wand with a shorter pistol style wand. After watching quite a few videos, I learned that most SunJoe products use a less common M22-15mm hose connection (female end on the hose). Most wands used a more common sized M22-14mm or 3/8" fitting. Since I purchased a Sooprinse High Pressure Washer Gun that came with the M22-14 fitting (male), I needed an adapter to bridge the gap.Internet searches pointed me towards a series of quick disconnects, swivels, and adapters to make all of those work. While it may be very functional and get the job done, I didn't want to buy that many adapters for a budget pressure washer to wash my cars with. In a nutshell, I needed an adapter from the SunJoe hose to a smaller wand/gun: M22-15mm male end to fit into the SunJoe hose, and M22-14mm female to fit into the wand/gun.This part fit perfectly and even came with a tiny bit of white teflon tape to seal the connections. I did add a slight amount of grease to the O-ring on the hose side before sliding it into the adapter, and used wrenches to tighten everything up as tight as I could. For my configuration, I have no swivel or quick disconnects, so the angle I set my gun relative to the natural curl of the hose is fixed. I fiddled with it a bit to get it as natural as I could, but once set and tightened, I was happy with the position and cleaned my patio with ease. Would a swivel help? Yeah, but the added expense and position where a leak could happen turned me away.If you are looking for this specific combination of SunJoe hose with Sooprinse High Pressure Washer Gun (https://www.amazon.com/gp/product/B07KPVM5MS/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1), then it will work!

I tried the YAMATIC adapter to mate the 15mm hose to a 14mm foam canon. The 14mm side fit perfectly, but the 15mm side did not work at all. Luckily, I saw a reference to the M MINGLE Pressure Washer Coupler. Other Sun Joe owners that tried using the more expensive YAMATIC adapter, have had the same problem. However, there is NO PROBLEM with the dimensions of the M MINGLE. This coupler is solid Brass, as opposed to the YAMATIC's mystery metal version. I'm pretty sure that one is plated Aluminum. I used my own pipe-thread tape, but since this is a Brass to Brass install with the foam canon, I probably don't need the tape. Both ends of the coupler do not leak under pressure. Perfect!

Great item, ease of installation and use A+++++++++++

I bought a new spray wand for my Sunjoe SPX and didn't realize the Sunjoe uses a 15mm connection and not a standard 14mm. So rather than return the wand I bought this and it worked fine. Only problem is you have to put teflon tape on the wand threads or it leaks. No mention of that in the description so beware is you buy one. Have some teflon tape handy.

I literally went to every hardware store like home depot, lowes ace hardware etc and no one carry this piece M22 with 15mm inlet and I was stressing so I came to amazon and this product was the first one pop up to me so I bought it right away ... this product fit 👌 on the spot no issues no leaks save the day ....

So far so good on the part. Connected to the pressure washer end of the hose to connect to my SunJoe pressure washer since all/most of the electrics have a M22 15MM connection. Objective was to create a quick connect for the hose. Part is solid and no leaks (I did use Teflon tape. To be clear, this part screws into the hose but you aren't done yet. Then you need to create the quick connect on the "water out" on the pressure washer. To do that I used https://www.amazon.com/gp/product/B07JVJN46S/ref=ppx_yo_dt_b_asin_title_o01__o00_s01?ie=UTF8&psc=1. Since the female side of this part is now 14MM (converting it to a standard measurement used by most of the pressure washer world), you can then screw in the male plug from the other part I linked above and connect the other part of the piece linked above to the pressure washer itself and voila, quick connect. Shouldn't be this hard but couldn't find any other solution.

I recently had to replace the hose and the wand for my AR Blue Clean AR390SS, but the connector on the end of the wand was an M22 14mm ID, while the connector on the end of the AR Blue Clean hose is an M22 15mm ID. This perfectly coupled the hose and wand, no leaks, and great pressure.I have to thank AR Blue Clean support for their help in identifying the actual hose size (I had no idea there was such a thing as M22 14ID, M22 15ID, I was expecting a standard 3/8" fitting). After a few orders and returns, I got it right and didn't have to replace the pressure washer itself.