Headliner Magic - 64 Inch Wide Automotive Headliners Foam Backed Material (5 Yards (180"), Ox Grey - 1808)

Ordered Ox Gray for a 2004 Mazda6 and it matched perfectly. Install was a breeze with 3M Super 77 Multipurpose Adhesive (in a spray can). I cleaned the old headliner off by peeling the fabric off, the using the brush attachment on a vacuum. Then I sprayed the cleanheadliner board onthe entire side facing in to the cabin, then spray the new headliner on the foam side, let them set and get tacky for a minute. Then I laid the new headliner on the board, smooth it out by hand, and trim it all leaving an inch to hang over the edge. Flipped it over, spraythe edges and folded over the excess to ensure it would be less likely to start hanging out again. Once installed back in the car, it looked brand new again.

I used this headliner fabric to renew the sagging headliner in my 1999 Dodge Dakota pickup. I ordered it in the Lt Natural color and this was a perfect match for the stock headliner. The 64" wide width was enough to cover the whole headliner with about 6" on each side. The headliner came rolled up in a long box. When I opened it, it had wrinkles down the center of it. I laid it out flat and let it sit for a while. The wrinkles became less prominent but did not come out completely. But when I installed the headliner, they pulled out and weren't a problem.To prepare my old headliner, I started by removing the original headliner fabric by just grabbing it on one edge and gently pulling it upward. This was easy since it was sagging and not adhered well anymore. That left some old foam stuck to the headliner shell. To get that off, I used a steel wire brush and carefully scraped it until all the foam was removed. This was tedious and took a long time. Once that was off, I laid the headliner fabric in place, sprayed it and pressed it down. Instead of spraying the whole headliner with glue and then doing it in one shot, I folded it in half, laid it into the shell and then sprayed a foot wide section. I let that glue cure a bit then pressed the fabric in place. I repeated this process until all of the fabric was glued down. I finished by cutting off the excess headliner and gluing the edges in place.I did make a couple of mistakes and maybe you can avoid them. First, in some places, I pressed too hard when pushing the fabric in place and it left indentations. This may have been a combination of too much pressure and too much glue. Second, the glue bonds instantly and repositioning the headliner is all but impossible so I had to be super careful when pushing it down. I accidentally had a wrinkle near the driver side a-pillar and I couldn't remove it since the headliner adhered well.For glue, I used the 3M headliner and foam adhesive that sells here on Amazon. It's really good stuff. To do a standard size headliner, I used about a can and a half, so order two cans of that glue. I let the glue set up about a minute before putting the pieces together and that seemed to be the right amount of time.The finished job, despite my mistakes, turned out really nicely. I'm quite happy with it.

Make sure you fit it well before glueing it in to place and spray the adhesive on both the liner and the foam roll it on tightly or it will be lumpy the fibers on the base should be flat and the fibers tight. before in stall I sprayed the adhesive one the base first and rolled it with a teflon roller to flatten out the fibers first. Fit it twice before glueing it in to place

This material exceeded expectations. It has a very plush, high quality feel to it, and has just enough stretch to make it form fitting. I was faced with the daunting task of replacing the headliner in a 2005 Mustang that has an electric sunroof. There are a lot of videos in headliner replacement, but I found none that dealt with working around a sunroof. Though it made the project more difficult for this “first timer”, the workability of this material made the job that much easier. Now I must admit that when I was using the old headliner as a pattern to mark and cut the openings for the sunvisors, rearview mirror, etc., I layed it out upside down so as not to get any of the old remaining foam on the new materia, and inadvertantly cut the opening for the sunroof switch on the wrong side of the dome light console. But this material allowed me to “patch” that mistake and even though it is in plain view, to this day, no one has noticed!

Overall I highly recommend this product. I am a first timer at replacing headliners. I pulled my 97 Geo metro headliner that was torn and sagging like no tomorrow. I used 3m fabric adhesive and laid this out trimming the excess once finished. Overall it laid out pretty well, but there were a few places that due to the sheer thickness of this product it made it very difficult to push the fabric down to get it to adhere. In the end though I am more than happy with their product.

The foam back material is awesome for headliner replacement. I have 2006 Mazda 6 and its headliner was falling constantly from the last couple of years, I tried to avoid it but recently in January 2019 it fell off completely from the backside and I wasn't able to see through my rear view mirror anymore. Then I decided to replace it, got some estimates from the local auto body shops, the lowest estimate that I got was of $225-250. Then I watched a whole lot of videos on YouTube on how to replace the headliners, replacing the headliner wasn't that tough itself. the only difficult part as to get the headliner out from the car and install it back.The material was delivered before the due date and it was packed very well. Regarding the dimension (2 Yards (72") it was enough to cover my whole headliner. I also got two cans of 3M 38808 Headliner and Fabric Adhesive, my only advice would be to spray it evenly and avoid over-spraying the adhesive because the excess adhesive will make the foam look bad. I over-sprayed at a couple of spots and it looks weird over those spots. Will update about the material if anything goes wrong with it.

My headliner started to looks like utter crap. I decided to do it myself for the first time and it looked like factory new ! Make sure to apply quality spray glue to this. I used 3M for this one.