RVCAZON STETION Quick Release Latch License Plate Lock Clip 1.25" Diameter Aluminum Alloy Car Hood Pins Lock Clip Kit for Bumper Hood License Plate (2 Pack - Red)

I wasn’t expecting much from these given the price point, but I’m pleased to say that these are actually quite good. They’re well designed, all metal, the latching mechanism holds tight, and the button has the right amount of pressure for a push release. They’re the right size for a larger hood and look much nicer than the old school pins that stick through.If you’re looking for this type of hood pin, this is a clean option. Fits not quite flush to the hood skin, as advertised, and has a nice, clean, modern look.You will have to be brave while you’re cutting the hole for the latch, but you got this. The wide flange is pretty forgiving of small mistakes, but if you’re unsure…get a body shop to install for you.

I used it to retain the front bumper on a race car.It worked well.

Hope the info below helps you who are brave enough to take on this challenge.This is an alternative to the standard-setting Quik-Latch brand. I have both and there is a difference in how they are mounted. This design has a smooth, round threaded ring requiring 3 set screws to lock it in place. (Quik-Latch uses a Hex threaded nut only).Hoods generally are designed with two sandwiched metal sheets, upper which you see and a structural lower sheet. You will need to drill large holes in each. You will need a much larger hole in the bottom sheet to access the 3 set screws, or you can do as I did and carefully locate the lock ring set screws, then drill clearance holes, as seen in attached photo) to secure the lock ring. (I purchased set screws and used a 3mm hex T-handle to tighten them after applying thread locker as I don't want set screws rolling around inside my hood later). Note that I drilled the 3 small holes in the hood underside because I didn't want an oversize hole in the structural sheet, as my hood is aluminum and needs as much "meat" as possible to ensure good, long life.Note that I gave a rating of 3 on ease to install....that rating is for the average tinkering person. You'll need a fair amount of patience, some not-so-normal tools, and some part layout skills.Remember that you also have the pins that secure to the radiator support that you must align with the latches. Be prepared to use some creativity and common sense in fabricating brackets (in some cases) for mounting the pins.Af for the part appearance, other buyers were concerned about discoloration. I purchased the silver color, and quickly found that it had a soft chrome finish, not some sort of anodized material. In an attempt to repair scratches, I tried to buff it. That didn't work well. When copper started to show through I realized I had to remove the entire chrome coating, completely revealing the aluminum underneath. I was pleased with the results. As you can see from the photo using wet 500 grit sandpaper on a rotating drill the finish has nice concentric rings and brushed finish, comparable to Quik-Latch brand.Overall it took a lot of work, but I feel the result was worth the effort. For the difference in price between this and Quik-Latch it was worth saving nearly $300 in my case.BTW...to keep the latch working well, ensure you have it adjusted well. If you have the closed adjustment too tight, you can have a LOT of trouble delatching the lock. Users may think the lock is at fault but installation adjustment may be at fault.Additionally, get some good silicone paste lubricant and keep the internal locking mechanism lubricated. Periodically do this, as some water may enter from above and have corrosives that may hinder optimum operation. This is the paste I got from Amazon for that purpose.Best wishes installing. Just be patient and with a bit of advance planning and layout you can have a good installation.

I was having problems with the original brackets and my bumper would come out on dips and speed bumps , it only took me 30min on my Evo x for both sides taking my time , all you need it drill bits from small to big , probably the best item I’ve ever bought for this price

Fácil de instalar y muy buena calidad

I used these to hold the bumper on my 15 mustang on. Install was very easy and they look great

Very easy to install and very happy with the results on my srt8 fiberglass hood for my 2011 dodge charger 5.7

The hood was bent when I bought the car, installed these hood pins and now the hood fits great! Would recommend using more expensive hole saws.